K35X40X17 bearing: complete specifications & equivalents
The K35X40X17 is a DIN 5402 radial bearing sized 35 x 40 x 17 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 35 mm |
| Outer diameter D | 40 mm |
| Width B | 17 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 19.8 kN |
| Basic static load rating C0 | 39 kN |
| Fatigue load limit Pu | 4.65 kN |
| Reference speed (thermal) | 12000 rpm |
| Limiting speed (mechanical) | 13000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 21 g |
| Manufacturer designation | K 35x40x17 |
| Standard | DIN 5402 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.1 needle roller and cage assemblies |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.1 needle roller and cage assemblies) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.1 needle roller and cage assemblies); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & K-series range
| Bore d | 1.378 in |
|---|---|
| Outer diameter D | 1.575 in |
| Width B | 0.669 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 2.5 mm |
| Smallest bore in K-series | 3 mm |
| Largest outer diameter in K-series | 63 mm |
| Width range across K-series | 7–32 mm |
| Bore position in K-series (smallest first) | 13 of 22 |
| Bore above smallest K-series size | 32 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the K35X40X17 model number is decoded
SKF lists K 35x40x17 in the K series of needle roller and cage assemblies: needle rollers caged at 35×40×17 mm, designed to run directly on a ground, hardened shaft and inside a machined housing bore. K 35×40×17 is a boundary plan, not an envelope: the assembly has no rings, so E 40 mm is the needle set diameter the housing bore must match, and the 35 mm journal must be ground and hardened. Because there are no rings, execution differences live in the cage: TN polymer cages reduce friction and noise, while the basic steel cage tolerates higher operating temperatures up to the lubricant limit. Minimum load matters: below roughly 0.02·C the rollers skid and smear; preloading the pivot or specifying a heavier execution avoids the glazing that pure oscillation produces on these raceways. Mounting: grind the 35 mm journal to the catalogue raceway tolerance after hardening to 58–64 HRC, bore the housing to E 40 mm H6, and slide the assembly in axially — pressing through the cage distorts it and locks the rollers.
Typical equipment & failure modes
Common applications
- universal joint crosses on commercial vehicles
- planetary gear pins in compact transmissions
- connecting rods of small compressors where radial height is critical
- rocker arm and rocker pin pivots on camshafts
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- corrosion pitting from condensation in intermittently operated machinery
- rapid raceway scoring when the shaft journal hardness drops below 58 HRC or the ground finish wears away
Selection pitfalls — read before you substitute
- At 35 mm bore, verify shaft deflection against the needle length: these rollers tolerate little edge loading, and a simply supported span between 35 mm seats can bend past the compensation range long before the load rating is exhausted.
- The quoted 19.8/39 kN ratings are SKF catalogue values for this exact execution (K 35x40x17); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- The 19.8/39 kN ratings and 21 g mass are SKF catalogue values transcribed from ch. 7.1 of PUB BU/P1 17000 (PDF table page 618); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What mounting mistakes ruin a K 35x40x17?
Slide the assembly over the ground 35 mm journal with a mounting sleeve, bore the housing to E 40 mm, and retain with a washer spanning the cage. Never press against the cage or rotate before the bearing is lubricated and loaded.
Is the K 35x40x17 sealed?
No — this execution is open and depends on the housing sealing arrangement; grease it at assembly and keep the relubrication interval short in dirty duty.
Which dimensions does the K 35x40x17 have?
A K 35x40x17 measures 35 mm bore/Fw × 40 mm outside diameter × 17 mm width (1.378 × 1.575 × 0.669 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 19.8 kN, static C0 39 kN, fatigue limit Pu 4.65 kN, limiting speed 13,000 r/min, reference speed 12,000 r/min, mass about 21 g.
What does K 35x40x17 mean in SKF part numbering?
K = needle roller and cage assembly (DIN 5402); the three figures give Fw 35 mm (shaft journal), E 40 mm (complement outside diameter, matched by the housing bore) and B 17 mm width. TN marks the glass fibre reinforced PA66 cage.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.1 needle roller and cage assemblies on 2026-09-26. Read our editorial & correction policy.