NK105-36 bearing: complete specifications & equivalents
The NK105-36 is a DIN 616 radial bearing sized 105 x 125 x 36 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 105 mm |
| Outer diameter D | 125 mm |
| Width B | 36 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 112 kN |
| Basic static load rating C0 | 265 kN |
| Fatigue load limit Pu | 32.5 kN |
| Reference speed (thermal) | 3800 rpm |
| Limiting speed (mechanical) | 4300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 710 g |
| Manufacturer designation | NK 105/36 |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NK-series range
| Bore d | 4.134 in |
|---|---|
| Outer diameter D | 4.921 in |
| Width B | 1.417 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 10 mm |
| Smallest bore in NK-series | 5 mm |
| Largest outer diameter in NK-series | 130 mm |
| Width range across NK-series | 10–40 mm |
| Bore position in NK-series (smallest first) | 45 of 46 |
| Bore above smallest NK-series size | 100 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NK105-36 model number is decoded
In SKF catalogue PUB BU/P1 17000, NK 105/36 designates a flanged, machined outer ring filled with needle rollers and a cage for a 105 mm shaft — heavier section and higher accuracy than a drawn cup, with no inner ring so the journal is the raceway. The letters identify a flanged machined outer ring without inner ring; the figures give 105 mm Fw and 36 mm B — dimensionally identical envelopes exist with an inner ring under the NA/NKI names, which changes the shaft seat entirely. The machined ring is through-hardened and ground on OD, bore-side raceway and faces; the flanged lip design means the housing shoulder can be omitted — the ring clamps axially between housing wall and cover washer. Catalogue mass 710 g at 105×125×36 mm makes this one of the highest capacity-per-gram choices in the machined-ring needle roller bearings without inner ring; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. Grease through the housing groove before fitting the shaft; the integral flanges hold the grease film at the roller ends, which is where these bearings first starve.
Typical equipment & failure modes
Common applications
- cam followers built up from separate components
- crank pins and eccentrics where the hardened journal is the raceway
- gearbox planetary and idler gears on hardened pins
- piston-pin style pivots in hydraulic pumps
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- hard-particle indentation in unfiltered lubricant
- rapid raceway scoring when the shaft journal hardness drops below 58 HRC or the ground finish wears away
Selection pitfalls — read before you substitute
- Above 50 mm bore, thermal growth matters: the 105 mm inner ring or journal grows with temperature faster than the housing, and the small clearance of a needle roller contact leaves little reserve — check running clearance hot, not just at assembly.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- Contamination, not fatigue, kills most small needle bearings: with raceways this narrow, one hard particle dents a full-width line — seal the housing even when the bearing execution itself is open.
- The 112/265 kN ratings and 710 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 634); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What limits the service life of a NK 105/36?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 105 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 10.0 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the NK 105/36?
A NK 105/36 measures 105 mm bore/Fw × 125 mm outside diameter × 36 mm width (4.134 × 4.921 × 1.417 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 112 kN, static C0 265 kN, fatigue limit Pu 32.5 kN, limiting speed 4,300 r/min, reference speed 3,800 r/min, mass about 710 g.
How is the NK 105/36 designation read?
NK names a machined-ring needle roller bearing without inner ring: the figures give Fw 105 mm and width 36 mm, OD 125 mm comes from the dimension series, and the flanged outer ring retains the caged rollers.
Can the NK 105/36 run on an unhardened shaft?
No. In this execution the 105 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.