NK25-16 bearing: complete specifications & equivalents
The NK25-16 is a DIN 616 radial bearing sized 25 x 33 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 25 mm |
| Outer diameter D | 33 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 15.1 kN |
| Basic static load rating C0 | 24.5 kN |
| Fatigue load limit Pu | 2.9 kN |
| Reference speed (thermal) | 16000 rpm |
| Limiting speed (mechanical) | 18000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 33 g |
| Manufacturer designation | NK 25/16 |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NK-series range
| Bore d | 0.984 in |
|---|---|
| Outer diameter D | 1.299 in |
| Width B | 0.63 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 4 mm |
| Smallest bore in NK-series | 5 mm |
| Largest outer diameter in NK-series | 130 mm |
| Width range across NK-series | 10–40 mm |
| Bore position in NK-series (smallest first) | 18 of 46 |
| Bore above smallest NK-series size | 20 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NK25-16 model number is decoded
NK 25/16 is a ribbed machined-ring needle roller bearing (no inner ring) sized 25×33×16 mm: the ground outside diameter seats in the housing, the integral flanges hold the rollers, and the 25 mm shaft journal completes the bearing. The NK 25/16 code states Fw 25 and width 16 mm directly; because the family has no inner ring, the 25 mm journal must be ground, hardened to 58–64 HRC and finished to the raceway tolerance the catalogue specifies. The machined ring is through-hardened and ground on OD, bore-side raceway and faces; the flanged lip design means the housing shoulder can be omitted — the ring clamps axially between housing wall and cover washer. Selection arithmetic: C 15.1 kN against C0 24.5 kN gives a C0/C ratio of 1.62, and the 2.9 kN fatigue load limit Pu sets the floor for the adjusted-life calculation at contaminated lubrication. Fit the outer ring with a press and a fitting sleeve, not by hammering the flanges — rolled flanges chip; the 33 mm ground OD takes the press fit that prevents outer-ring creep in oscillating duty.
Typical equipment & failure modes
Common applications
- crank pins and eccentrics where the hardened journal is the raceway
- gearbox planetary and idler gears on hardened pins
- piston-pin style pivots in hydraulic pumps
- guide rollers running on hardened tracks
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- cage pocket wear and roller skew after sustained operation with too little radial preload
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- false brinelling of standby equipment under external vibration
- smearing of rollers and journal during idle periods because the radial section holds too little lubricant
Selection pitfalls — read before you substitute
- On a 25 mm seat the housing bore quality dominates life: a bore 0.02 mm out of round pinches the 33 mm ring or cup into a lobed shape, and the rollers then trace the housing's geometry error, not the design load.
- Do not interchange envelope-identical needle families blindly: NK 25/16 shares its 25×33×16 mm outline with inner-ring and sealed siblings whose ratings differ — the family letters are part of the specification, not decoration.
- Reference and limiting speeds are different limits: the 16,000 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- The 15.1/24.5 kN ratings and 33 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 628); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Can the NK 25/16 run on an unhardened shaft?
No. In this execution the 25 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
How should the NK 25/16 be mounted?
Press on the ring faces only with a fitting sleeve, keep everything square to the 25 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
What limits the service life of a NK 25/16?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 25 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 4.0 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the NK 25/16?
A NK 25/16 measures 25 mm bore/Fw × 33 mm outside diameter × 16 mm width (0.984 × 1.299 × 0.63 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 15.1 kN, static C0 24.5 kN, fatigue limit Pu 2.9 kN, limiting speed 18,000 r/min, reference speed 16,000 r/min, mass about 33 g.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.