NK37-30 bearing: complete specifications & equivalents
The NK37-30 is a DIN 616 radial bearing sized 37 x 47 x 30 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 37 mm |
| Outer diameter D | 47 mm |
| Width B | 30 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 36.9 kN |
| Basic static load rating C0 | 76.5 kN |
| Fatigue load limit Pu | 9.5 kN |
| Reference speed (thermal) | 11000 rpm |
| Limiting speed (mechanical) | 12000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 110 g |
| Manufacturer designation | NK 37/30 |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NK-series range
| Bore d | 1.457 in |
|---|---|
| Outer diameter D | 1.85 in |
| Width B | 1.181 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 5 mm |
| Smallest bore in NK-series | 5 mm |
| Largest outer diameter in NK-series | 130 mm |
| Width range across NK-series | 10–40 mm |
| Bore position in NK-series (smallest first) | 25 of 46 |
| Bore above smallest NK-series size | 32 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NK37-30 model number is decoded
In SKF catalogue PUB BU/P1 17000, NK 37/30 designates a flanged, machined outer ring filled with needle rollers and a cage for a 37 mm shaft — heavier section and higher accuracy than a drawn cup, with no inner ring so the journal is the raceway. The NK 37/30 code states Fw 37 and width 30 mm directly; because the family has no inner ring, the 37 mm journal must be ground, hardened to 58–64 HRC and finished to the raceway tolerance the catalogue specifies. The machined ring is through-hardened and ground on OD, bore-side raceway and faces; the flanged lip design means the housing shoulder can be omitted — the ring clamps axially between housing wall and cover washer. For life calculation, the 36.9/76.5 kN ratings assume raceway geometry supplied by the shaft and housing in families without an inner ring — journal hardness, roundness and finish are part of the bearing, not of the application. Mounting: the flanged outer ring presses into the H7 housing bore against its flange face; the shaft (hardened to 58–64 HRC, ground) enters afterwards, and axial retention is by the housing wall plus a cover washer.
Typical equipment & failure modes
Common applications
- guide rollers running on hardened tracks
- swing arms and lever pivots with oscillating duty
- cam followers built up from separate components
- crank pins and eccentrics where the hardened journal is the raceway
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- corrosion pitting from condensation in intermittently operated machinery
- rapid raceway scoring when the shaft journal hardness drops below 58 HRC or the ground finish wears away
Selection pitfalls — read before you substitute
- At 37 mm bore, verify shaft deflection against the needle length: these rollers tolerate little edge loading, and a simply supported span between 37 mm seats can bend past the compensation range long before the load rating is exhausted.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- Contamination, not fatigue, kills most small needle bearings: with raceways this narrow, one hard particle dents a full-width line — seal the housing even when the bearing execution itself is open.
- The 36.9/76.5 kN ratings and 110 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 630); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
How should the NK 37/30 be mounted?
Press on the ring faces only with a fitting sleeve, keep everything square to the 37 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
What limits the service life of a NK 37/30?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 37 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 5.0 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the NK 37/30?
A NK 37/30 measures 37 mm bore/Fw × 47 mm outside diameter × 30 mm width (1.457 × 1.85 × 1.181 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 36.9 kN, static C0 76.5 kN, fatigue limit Pu 9.5 kN, limiting speed 12,000 r/min, reference speed 11,000 r/min, mass about 110 g.
How is the NK 37/30 designation read?
NK names a machined-ring needle roller bearing without inner ring: the figures give Fw 37 mm and width 30 mm, OD 47 mm comes from the dimension series, and the flanged outer ring retains the caged rollers.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.