NK43-20 bearing: complete specifications & equivalents
The NK43-20 is a DIN 616 radial bearing sized 43 x 53 x 20 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 43 mm |
| Outer diameter D | 53 mm |
| Width B | 20 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 27.5 kN |
| Basic static load rating C0 | 55 kN |
| Fatigue load limit Pu | 6.8 kN |
| Reference speed (thermal) | 9500 rpm |
| Limiting speed (mechanical) | 11000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 86 g |
| Manufacturer designation | NK 43/20 |
| Standard | DIN 616 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & NK-series range
| Bore d | 1.693 in |
|---|---|
| Outer diameter D | 2.087 in |
| Width B | 0.787 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 5 mm |
| Smallest bore in NK-series | 5 mm |
| Largest outer diameter in NK-series | 130 mm |
| Width range across NK-series | 10–40 mm |
| Bore position in NK-series (smallest first) | 29 of 46 |
| Bore above smallest NK-series size | 38 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the NK43-20 model number is decoded
NK 43/20 is a ribbed machined-ring needle roller bearing (no inner ring) sized 43×53×20 mm: the ground outside diameter seats in the housing, the integral flanges hold the rollers, and the 43 mm shaft journal completes the bearing. The NK 43/20 code states Fw 43 and width 20 mm directly; because the family has no inner ring, the 43 mm journal must be ground, hardened to 58–64 HRC and finished to the raceway tolerance the catalogue specifies. Execution notes: the outer ring flanges are rolled from the ring material (no loose ribs to dislodge), the roller set is caged for low friction, and the TN option swaps in a polymer cage for quieter running. For life calculation, the 27.5/55 kN ratings assume raceway geometry supplied by the shaft and housing in families without an inner ring — journal hardness, roundness and finish are part of the bearing, not of the application. Grease through the housing groove before fitting the shaft; the integral flanges hold the grease film at the roller ends, which is where these bearings first starve.
Typical equipment & failure modes
Common applications
- guide rollers running on hardened tracks
- swing arms and lever pivots with oscillating duty
- cam followers built up from separate components
- crank pins and eccentrics where the hardened journal is the raceway
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- hard-particle indentation in unfiltered lubricant
- smearing of rollers and journal during idle periods because the radial section holds too little lubricant
Selection pitfalls — read before you substitute
- At 43 mm bore, verify shaft deflection against the needle length: these rollers tolerate little edge loading, and a simply supported span between 43 mm seats can bend past the compensation range long before the load rating is exhausted.
- Hardness is load capacity: in families without an inner ring the 43 mm journal must hold 58–64 HRC with a ground finish; a surface that looks fine but sits at 45 HRC will rib the raceway within weeks.
- The quoted 27.5/55 kN ratings are SKF catalogue values for this exact execution (NK 43/20); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- The 27.5/55 kN ratings and 86 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 630); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Can the NK 43/20 run on an unhardened shaft?
No. In this execution the 43 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
How should the NK 43/20 be mounted?
Press on the ring faces only with a fitting sleeve, keep everything square to the 43 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
What limits the service life of a NK 43/20?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 43 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 5.0 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the NK 43/20?
A NK 43/20 measures 43 mm bore/Fw × 53 mm outside diameter × 20 mm width (1.693 × 2.087 × 0.787 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 27.5 kN, static C0 55 kN, fatigue limit Pu 6.8 kN, limiting speed 11,000 r/min, reference speed 9,500 r/min, mass about 86 g.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.