RNA4919 bearing: complete specifications & equivalents
The RNA4919 is a ISO 1206 radial bearing sized 110 x 130 x 35 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 110 mm |
| Outer diameter D | 130 mm |
| Width B | 35 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 114 kN |
| Basic static load rating C0 | 270 kN |
| Fatigue load limit Pu | 33.5 kN |
| Reference speed (thermal) | 3600 rpm |
| Limiting speed (mechanical) | 4000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 720 g |
| Manufacturer designation | RNA 4919 |
| Standard | ISO 1206 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & RNA-49-series range
| Bore d | 4.331 in |
|---|---|
| Outer diameter D | 5.118 in |
| Width B | 1.378 in |
| ISO bore code | 19 |
| Radial section height (D−d)/2 | 10 mm |
| Smallest bore in RNA-49-series | 14 mm |
| Largest outer diameter in RNA-49-series | 190 mm |
| Width range across RNA-49-series | 13–50 mm |
| Bore position in RNA-49-series (smallest first) | 23 of 28 |
| Bore above smallest RNA-49-series size | 96 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the RNA4919 model number is decoded
RNA 4919 is a machined-ring needle roller bearing without an inner ring: a solid outer ring with integral flanges guiding the caged rollers, riding directly on a 110 mm hardened shaft journal, as listed in SKF catalogue PUB BU/P1 17000. The letters identify a flanged machined outer ring without inner ring; the figures give 110 mm Fw and 35 mm B — dimensionally identical envelopes exist with an inner ring under the NA/NKI names, which changes the shaft seat entirely. The machined ring is through-hardened and ground on OD, bore-side raceway and faces; the flanged lip design means the housing shoulder can be omitted — the ring clamps axially between housing wall and cover washer. Catalogue mass 720 g at 110×130×35 mm makes this one of the highest capacity-per-gram choices in the dimension series 49 needle roller bearings without inner ring; the limit is usually the shaft's ability to serve as a raceway, not the rolling contact itself. Grease through the housing groove before fitting the shaft; the integral flanges hold the grease film at the roller ends, which is where these bearings first starve.
Typical equipment & failure modes
Common applications
- cam followers built up from separate components
- crank pins and eccentrics where the hardened journal is the raceway
- gearbox planetary and idler gears on hardened pins
- piston-pin style pivots in hydraulic pumps
Known failure patterns
- raceway spalling once the catalogue L10 life is exceeded or after overload events
- polymer cage deformation when the local temperature exceeds the 120 °C sustained limit
- abrasive paste formation from dust ingressing past open ends without effective housing seals
- hard-particle indentation in unfiltered lubricant
- rapid raceway scoring when the shaft journal hardness drops below 58 HRC or the ground finish wears away
Selection pitfalls — read before you substitute
- Above 50 mm bore, thermal growth matters: the 110 mm inner ring or journal grows with temperature faster than the housing, and the small clearance of a needle roller contact leaves little reserve — check running clearance hot, not just at assembly.
- Do not interchange envelope-identical needle families blindly: RNA 4919 shares its 110×130×35 mm outline with inner-ring and sealed siblings whose ratings differ — the family letters are part of the specification, not decoration.
- Reference and limiting speeds are different limits: the 3,600 r/min reference is the thermal criterion under load, The limiting value is mechanical; the reference value is thermal under load, and grease choice moves it substantially.
- The 114/270 kN ratings and 720 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 636); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
Can the RNA 4919 run on an unhardened shaft?
No. In this execution the 110 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
How should the RNA 4919 be mounted?
Press on the ring faces only with a fitting sleeve, keep everything square to the 110 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
What limits the service life of a RNA 4919?
Beyond the L10 rating, the practical limits are journal/raceway hardness for the 110 mm seat, lubricant condition at the roller ends, and contamination through open ends — the 10.0 mm radial section leaves no reserve once a raceway is dented or ribboned.
What are the dimensions and ratings of the RNA 4919?
A RNA 4919 measures 110 mm bore/Fw × 130 mm outside diameter × 35 mm width (4.331 × 5.118 × 1.378 in). From SKF catalogue PUB BU/P1 17000: radial dynamic rating C 114 kN, static C0 270 kN, fatigue limit Pu 33.5 kN, limiting speed 4,000 r/min, reference speed 3,600 r/min, mass about 720 g.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.