RNA6919 bearing: complete specifications & equivalents
The RNA6919 is a ISO 1206 radial bearing sized 110 x 130 x 63 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 110 mm |
| Outer diameter D | 130 mm |
| Width B | 63 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | none |
| Basic dynamic load rating C | 172 kN |
| Basic static load rating C0 | 465 kN |
| Fatigue load limit Pu | 56 kN |
| Reference speed (thermal) | 3600 rpm |
| Limiting speed (mechanical) | 4000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1450 g |
| Manufacturer designation | RNA 6919 |
| Standard | ISO 1206 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & RNA-69-series range
| Bore d | 4.331 in |
|---|---|
| Outer diameter D | 5.118 in |
| Width B | 2.48 in |
| ISO bore code | 19 |
| Radial section height (D−d)/2 | 10 mm |
| Smallest bore in RNA-69-series | 16 mm |
| Largest outer diameter in RNA-69-series | 130 mm |
| Width range across RNA-69-series | 22–63 mm |
| Bore position in RNA-69-series (smallest first) | 22 of 22 |
| Bore above smallest RNA-69-series size | 94 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the RNA6919 model number is decoded
Where the shaft can be hardened and ground, SKF offers RNA 6919 in the dimension series 69 needle roller bearings without inner ring: outer ring only, needle rollers caged between integral flanges, 110 mm bore seat and 130 mm OD. Reading the designation: RNA gives the series and the numbers the boundary plan — 110 mm Fw for the shaft seat, 63 mm width; the 130 mm OD comes from the dimension series, and the absence of an inner ring is built into the family name. SKF offers this family open as standard; a matching IR inner ring can be added separately when the shaft cannot be hardened, which converts the envelope into the NKI/NA equivalent. For life calculation, the 172/465 kN ratings assume raceway geometry supplied by the shaft and housing in families without an inner ring — journal hardness, roundness and finish are part of the bearing, not of the application. Grease through the housing groove before fitting the shaft; the integral flanges hold the grease film at the roller ends, which is where these bearings first starve.
Typical equipment & failure modes
Common applications
- guide rollers running on hardened tracks
- swing arms and lever pivots with oscillating duty
- cam followers built up from separate components
- crank pins and eccentrics where the hardened journal is the raceway
Known failure patterns
- needle edge loading and raceway denting when the shaft deflects beyond the compensation range
- cage pocket wear and roller skew after sustained operation with too little radial preload
- grease starvation at the roller ends when relubrication intervals are stretched in dirty duty
- electrical erosion on VFD-driven shafts without brush or insulated mounting
- rapid raceway scoring when the shaft journal hardness drops below 58 HRC or the ground finish wears away
Selection pitfalls — read before you substitute
- Above 50 mm bore, thermal growth matters: the 110 mm inner ring or journal grows with temperature faster than the housing, and the small clearance of a needle roller contact leaves little reserve — check running clearance hot, not just at assembly.
- The quoted 172/465 kN ratings are SKF catalogue values for this exact execution (RNA 6919); ratings can be revised without the order number changing, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the drawing.
- Oscillating pivots fail differently: rocking through a small angle concentrates wear in the same roller positions — inspect those zones, and consider rotating the assembly's clock position at service intervals.
- The 172/465 kN ratings and 1450 g mass are SKF catalogue values transcribed from ch. 7.3 of PUB BU/P1 17000 (PDF table page 636); combined-type axial ratings appear in the text above because the structured record carries radial values only.
Frequently asked questions
What does RNA 6919 mean in SKF part numbering?
RNA names a machined-ring needle roller bearing without inner ring: the figures give Fw 110 mm and width 63 mm, OD 130 mm comes from the dimension series, and the flanged outer ring retains the caged rollers.
Does the RNA 6919 need a hardened and ground shaft?
No. In this execution the 110 mm shaft journal is the inner raceway: it must be ground and hardened to 58–64 HRC (with matching housing bore quality on the outside). If the shaft cannot meet that, order the inner-ring sibling (NKI/NA execution) plus its ground inner ring instead.
What mounting mistakes ruin a RNA 6919?
Press on the ring faces only with a fitting sleeve, keep everything square to the 110 mm seat, and never transmit force through the rolling elements. Follow the catalogue's seat tolerances — the narrow needle contact forgives neither tilt nor burrs.
Is the RNA 6919 sealed?
No — this execution is open and depends on the housing sealing arrangement; grease it at assembly and keep the relubrication interval short in dirty duty.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 7.3 machined rings with flanges, without an inner ring on 2026-09-26. Read our editorial & correction policy.