29244-E bearing: complete specifications & equivalents
The 29244-E is a ISO 104 radial bearing sized 220 x 300 x 48 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 220 mm |
| Outer diameter D | 300 mm |
| Width B | 48 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 690 kN |
| Basic static load rating C0 | 3000 kN |
| Fatigue load limit Pu | 310 kN |
| Reference speed (thermal) | 1300 rpm |
| Limiting speed (mechanical) | 2200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 10000 g |
| Manufacturer designation | 29244 E |
| Standard | ISO 104 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 13.1 spherical roller thrust bearings |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 13.1 spherical roller thrust bearings) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 13.1 spherical roller thrust bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 29200-series range
| Bore d | 8.661 in |
|---|---|
| Outer diameter D | 11.811 in |
| Width B | 1.89 in |
| ISO bore code | 44 |
| Radial section height (D−d)/2 | 40 mm |
| Smallest bore in 29200-series | 150 mm |
| Largest outer diameter in 29200-series | 1060 mm |
| Width range across 29200-series | 39–155 mm |
| Bore position in 29200-series (smallest first) | 4 of 23 |
| Bore above smallest 29200-series size | 70 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the 29244-E model number is decoded
29244 E is a spherical roller thrust bearing to ISO 104 in the high-speed 292 series: asymmetrical barrel rollers running on a sphered housing washer, sized 220×300×48 mm, as listed in SKF catalogue PUB BU/P1 17000 ch. 13.1. The designation 29244 E separates into 292 (series), 44 (220 mm bore) and E; washers are separable for individual mounting. The stamped steel E window cage is matched to size: the E design is the current standard with a stamped window-type steel cage. The sphered housing washer self-aligns during mounting and under shaft deflection. Static safety matters for shock duty: compare peak axial force against C0 3000 kN with the application's static factor, since crane hooks and screw positions see their worst load at zero or low speed. Verify the minimum axial load (factor A 0.86) immediately at commissioning — a cold start unloaded smears the rollers; spring preload or rotor weight must be present before the shaft rotates.
Typical equipment & failure modes
Common applications
- marine shaft and rudder-style thrust positions with seat deflection
- paper machine calender and refiner discs with combined axial and radial force
- crane hook assemblies where the hook block turns under full load
- injection moulding machine and extruder screw thrust positions
Known failure patterns
- cage wear from rollers being dragged through unloaded zones under fluctuating thrust
- washer back-face fretting where the seat is too narrow to support the full ring face
- abrasive paste forming as dust bypasses the housing seals into the open washer set
- false brinelling and rust-red witness marks on standby machines under external vibration
- roller skidding and raceway glazing once the thrust falls below the catalogue minimum axial load (factor A)
Selection pitfalls — read before you substitute
- At 220 mm bore, oil flow becomes the design variable: the 690 kN rating assumes fresh oil at the contact, and a blocked feed groove halves real life.
- the 1,300 r/min reference speed is the thermal criterion under load, the 2,200 r/min limiting speed is the mechanical ceiling; large 292 bearings are normally run well below it with oil cooling.
- Radial force beyond the permitted fraction of simultaneous thrust (about 0.55·F_a) overloads one side of the barrel-roller set — add a radial bearing instead of leaning on 29244 E.
- The 690/3000 kN figures assume the matching sphered seating washer is fitted where the catalogue calls for it; a flat housing seat removes the self-aligning function.
- Minimum load factor A 0.86 dominates commissioning: start the oil flow and preload before rotation, especially on 292 bearings where an unloaded cold start smears the rollers.
- The 690/3000 kN ratings and 10000 g mass are SKF catalogue values transcribed from ch. 13.1 of PUB BU/P1 17000 (PDF table page 926); mounting data — the minimum axial load factor A — appears in the running text because the structured record carries the boundary envelope only.
Frequently asked questions
What are the dimensions and ratings of the 29244 E?
A 29244 E measures 220 mm bore × 300 mm outside diameter × 48 mm width (8.661 × 11.811 × 1.89 in). From SKF catalogue PUB BU/P1 17000: dynamic C 690 kN, static C0 3000 kN, fatigue limit Pu 310 kN, reference speed 1,300 r/min, limiting speed 2,200 r/min, mass about 10000 g. Minimum axial load factor A 0.86 must be maintained in service.
How is the 29244 E designation read?
292 is the dimension series (high-speed 292 series) and 44 the 220 mm bore (code 44 × 5); E is the cage execution (stamped steel E window cage). The sphered housing washer provides self-alignment.
Why is the minimum axial load (A 0.86) so important?
Spherical roller thrust bearings skid and smear immediately when run unloaded — on large sizes factor A 0.86 corresponds to a substantial force. Springs, oil lift or the rotor/load weight must be applied before rotation, including cold test runs.
Can the 29244 E also carry radial load?
Yes, up to roughly 55 % of the simultaneous axial force, thanks to the steep contact angle of the barrel rollers. Beyond that mix, specify a separate radial bearing; the primary duty remains one-direction thrust.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 13.1 spherical roller thrust bearings on 2026-09-27. Read our editorial & correction policy.