22207-EK bearing: complete specifications & equivalents
The 22207-EK is a ISO 15 radial bearing sized 35 x 72 x 23 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 35 mm |
| Outer diameter D | 72 mm |
| Width B | 23 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 88.8 kN |
| Basic static load rating C0 | 85 kN |
| Fatigue load limit Pu | 9.3 kN |
| Reference speed (thermal) | 9000 rpm |
| Limiting speed (mechanical) | 12000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 590 g |
| Manufacturer designation | SKF 22207 EK |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 22200-series range
| Bore d | 1.378 in |
|---|---|
| Outer diameter D | 2.835 in |
| Width B | 0.906 in |
| ISO bore code | 07 |
| Radial section height (D−d)/2 | 18.5 mm |
| Smallest bore in 22200-series | 25 mm |
| Largest outer diameter in 22200-series | 290 mm |
| Width range across 22200-series | 18–80 mm |
| Bore position in 22200-series (smallest first) | 3 of 22 |
| Bore above smallest 22200-series size | 10 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22207 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:12) sleeve-mounted execution of 22207; identical ISO 15 envelope, fits H307 adapter sleeve on a 30 mm shaft. |
| C2207-TN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF CARB toroidal bearing C 2207 TN9 shares the 35×72×23 mm envelope with ratings within 10 %; it self-aligns but floats axially and cannot locate the shaft — locating/non-locating pair, not a substitute. |
| C2207-KTN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF CARB toroidal bearing C 2207 KTN9 shares the 35×72×23 mm envelope with ratings within 10 %; it self-aligns but floats axially and cannot locate the shaft — locating/non-locating pair, not a substitute. |
| C2207-V | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF CARB toroidal bearing C 2207 V shares the 35×72×23 mm envelope but catalogue C/C0 differ (95/96 kN vs 88.8/85 kN); it floats axially and cannot locate the shaft — pair, never swap one-for-one. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22207-EK model number is decoded
In SKF catalogue PUB BU/P1 17000, 22207-ek denotes the tapered-bore version (K suffix, taper 1:12) of the 22200-series spherical roller bearing: dimensioned 35×72×23 mm, it seats on an adapter or withdrawal sleeve rather than directly on a machined journal. The code breaks down as type digit 2 (double-row spherical roller), dimension series 22 (dimension series 22 (medium OD, wide)), and bore code 07 = 35 mm; dimensions 35×72×23 mm therefore match the ISO 15 envelope. The K in the designation marks the 1:12 tapered bore: SKF mounts it on an H-series adapter sleeve (with KM locknut and MB lock washer) on a plain commercial-grade shaft, or on an AH withdrawal sleeve where the bearing must abut a shaft shoulder. Catalogue mass 590 g for the 35×72×23 mm open execution covers the two pressed-steel cages with a floating guide ring; tapered-bore and sealed variants differ in mass and carry their own order numbers. On an H adapter sleeve the 35 mm shaft seat only needs an h9 plain journal; slide the sleeve into the 22207-ek inner ring, tighten the KM nut against the MB washer until the catalogue clearance-reduction value is reached, then lock the washer tab.
Typical equipment & failure modes
Common applications
- hammer-mill and crusher rotors
- continuous-caster guide rolls
- fan and pulley shafts that need periodic bearing removal in the field
- shafting produced to commercial tolerances, where the adapter sleeve supplies the precision seat
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- fretting corrosion and sleeve-seat scoring when drive-up is insufficient and the tapered inner ring creeps on the adapter sleeve
- surface distress and smearing when the relubrication interval is exceeded — the W33 groove is only effective if grease actually reaches the roller rows
- rolling-contact fatigue spalling after the rated L10 life is exceeded
Selection pitfalls — read before you substitute
- On this 35 mm bore, an interference inner-ring fit consumes a large share of the CN clearance; specify C3 when the inner ring rotates hot, and verify residual clearance after mounting rather than trusting the catalogue clearance class.
- The 22200-series series at 35 mm bore (72×23 mm) is the general-purpose spherical roller envelope; stepping up to 223 adds capacity and width, stepping to 230 trims the OD — neither is interchangeable without re-checking shoulders and speed.
- Never apply the drive-up or clearance-reduction figures for this 1:12 tapered 22207-ek to a bearing of the other taper (1:12 vs 1:30); the steeper taper moves far less clearance per nut turn and the targets come from different catalogue tables.
- The adapter sleeve is selected by actual shaft diameter, not by the 35 mm nominal bearing bore: H-sleeve part numbers span a small diameter range, so two different shaft diameters can use the same 22207-ek with different sleeves.
- Open spherical roller bearings rely on the housing seals; in screening or crusher duty a failed seal lets grit into the sphered raceway and the 22207-ek pits long before its L10 life.
- The 88.8/85 kN ratings are SKF catalogue values for this tapered-bore execution (SKF 22207 EK); sleeve, KM nut and MB washer are separate order numbers, and the catalogue version (SKF catalogue PUB BU/P1 17000) should travel with the mounting specification.
Frequently asked questions
What are the dimensions and catalogue data of 22207-ek?
The SKF 22207 EK is a double-row spherical roller bearing with a 1:12 tapered bore, 35 mm nominal bore, 72 mm outer diameter and 23 mm width (1.378 × 2.835 × 0.906 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: C 88.8 kN, C0 85 kN, Pu 9.3 kN, reference speed 9,000 r/min, limiting speed 12,000 r/min, mass about 590 g. It is mounted on an adapter (H) or withdrawal (AH) sleeve, not directly on the shaft.
What does the K suffix mean on 22207-ek?
K marks a 1:12 tapered bore for sleeve mounting — SKF writes EK or CCK(/W33), FAG writes -K- inside the suffix chain for sleeve mounting. The bearing seats on an H-series adapter sleeve with a KM locknut and MB lock washer (plain shaft, h9 tolerance), or on an AH withdrawal sleeve against a shaft shoulder. The rarer K30 suffix would instead mean a 1:30 taper; dimension series 40/41 spherical rollers commonly use it.
Which adapter sleeve fits the 22207-ek?
The sleeve is selected by the actual shaft diameter in millimetres, not only by the 35 mm nominal bore: SKF H-sleeve numbers each cover a small shaft-diameter range and are width-series specific (H39/H30/H31/H32 matching dimension series 39/40/31/32), and each kit bundles the sleeve, KM locknut and MB lock washer. For shoulder locations use an AH withdrawal sleeve instead. Confirm the sleeve number against the SKF catalogue PUB BU/P1 17000 mounting tables for your shaft size.
How is the 22207-ek driven up and checked?
Mounting is controlled by radial-clearance reduction or axial drive-up distance from the SKF catalogue tables for the 1:12 taper, never by locknut torque. Measure clearance with feeler gauges before and after tightening the KM nut, stop at the tabulated decrease, and lock the MB washer tab. Over-drive removes too much clearance (inner-ring cracking risk); under-drive lets the sleeve creep and fret.
What is the difference between 22207-ek and 22207?
They share the ISO 15 envelope and the same 88.8/85 kN ratings, but 22207-ek has the 1:12 tapered bore for sleeve mounting on a plain shaft, while 22207 has a cylindrical bore for direct mounting on a machined interference journal (typically k5 with H7 housing). They are separate order numbers, not interchangeable in the same shaft arrangement.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.2 adapter-sleeve executions on 2026-09-26. Read our editorial & correction policy.