22232EAD1 bearing: complete specifications & equivalents
The 22232EAD1 is a ISO 15 radial bearing sized 160 x 290 x 80 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 160 mm |
| Outer diameter D | 290 mm |
| Width B | 80 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1220 kN |
| Basic static load rating C0 | 1390 kN |
| Fatigue load limit Pu | 84.1 kN |
| Limiting speed (mechanical) | 1700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 22300 g |
| Manufacturer designation | NTN 22232EAD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 22200-series range
| Bore d | 6.299 in |
|---|---|
| Outer diameter D | 11.417 in |
| Width B | 3.15 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 65 mm |
| Smallest bore in 22200-series | 25 mm |
| Largest outer diameter in 22200-series | 580 mm |
| Width range across 22200-series | 18–150 mm |
| Bore position in 22200-series (smallest first) | 22 of 32 |
| Bore above smallest 22200-series size | 135 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22232EAKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 22200-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 22232EAKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22232EAD1 model number is decoded
22232EAD1 is the EA pressed-steel-cage execution of NTN's spherical roller range for a 160 mm shaft — 1220 kN basic dynamic capacity in a 22300 g, open ISO 15 envelope. Numbering ties 22232EAD1 to its envelope and execution: same-number EA versus EM or plain variants share the 160 mm bore but differ in cage and sometimes mass, so they are quoted as separate articles. The D1 outer-ring annular oil groove with holes makes relubrication part of the design: fresh grease reaches the rolling elements through the outer-ring feature rather than relying solely on end-side packing. Equivalent-load planning keeps a radial plus moderate axial combination on 22232EAD1; if the axial component dominates, pair with a thrust bearing rather than running one roller row unloaded. Never mount 22232EAD1 by striking the outer ring through the roller set; drive through ring faces (or the adapter sleeve nut) and support the ring square to avoid brinelling the 290 mm race.
Typical equipment & failure modes
Common applications
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
- steel-mill and heavy crusher main shafts
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
- rolling-contact fatigue after the catalogue L10 life at the actual load
Selection pitfalls — read before you substitute
- At 160 mm bore 22232EAD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 1,700 r/min grease rating is lost to abrasive wear long before fatigue.
- Minimum load must be maintained even at rest under vibration: an unloaded 22232EAD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- Minimum load must be maintained even at rest under vibration: an unloaded 22232EAD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- K and K30 are different tapers — K is 1:12 and K30 is 1:30 on the wide series; an adapter sleeve for one will not mount the other 160 mm bearing, and drive-up procedures differ.
- The 1220/1390 kN ratings, 84.1 kN Pu and 22300 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 22232EAD1 (EA pressed-steel-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 22232EAD1?
22232EAD1 is an NTN double-row spherical roller bearing to ISO 15: 160 mm bore, 290 mm OD and 80 mm width (6.299 × 11.417 × 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 1220 kN, C0 1390 kN, Pu 84.1 kN, grease limiting speed 1,700 r/min, oil 2,100 r/min, mass about 22300 g. It is open, with pressed sheet-steel window cage (EA high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
22232EAD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 22232EAKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 22232EAD1 is the EA pressed-steel-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 22232EAD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 22232EAD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 22232EAD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 22200 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 1220 kN C / 1390 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.