160×290×80 mm bearings

19 models from 3 brands across 2 types share this ISO 15 envelope: 160 mm bore, 290 mm outside diameter, 80 mm width (6.299×11.417×3.150 in), 65 mm radial section.

19 models fit this space 3 brands 19 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22232 Spherical Roller SKF open CN 1043 1290 22500
22232-CCK-W33 Spherical Roller SKF open CN 1043 1290 29500
22232EAD1 Spherical Roller NTN open CN 1220 1390 22300
22232EAKD1 Spherical Roller NTN open CN 1220 1390 21800
22232EMD1 Spherical Roller NTN open CN 1220 1390 22900
22232EMKD1 Spherical Roller NTN open CN 1220 1390 22400
N2232 Cylindrical Roller NTN open CN 700 940 21600
NCF2232-ECJB Cylindrical Roller SKF open CN 980 1270 23500
NCF2232-V Cylindrical Roller SKF open CN 990 1500 23000
NJ2232 Cylindrical Roller NTN open CN 700 940 21600
NJ2232-ECML Cylindrical Roller SKF open CN 930 1200 23500
NJ2232E Cylindrical Roller NTN open CN 895 1190 —
NU2232 Cylindrical Roller NTN open CN 700 940 21600
NU2232-ECML Cylindrical Roller SKF open CN 930 1200 23000
NU2232E Cylindrical Roller NTN open CN 895 1190 —
NUH2232-ECMH Cylindrical Roller SKF open CN 980 1270 23000
NUP2232 Cylindrical Roller NTN open CN 700 940 21600
NUP2232E Cylindrical Roller NTN open CN 895 1190 —
SL182232 Cylindrical Roller FAG open CN 1020 1470 23000

Note: catalogue dynamic load ratings for this envelope span 700.0– 1220.0 kN — a 74% spread between designs in the very same 160×290×80 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 160 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22232, 22232-CCK-W33, 22232EAD1, 22232EAKD1, 22232EMD1, 22232EMKD1, N2232, NCF2232-ECJB, NCF2232-V, NJ2232, NJ2232-ECML, NJ2232E, NU2232, NU2232-ECML, NU2232E, NUH2232-ECMH, NUP2232, NUP2232E, SL182232.

Frequently asked questions

Are all 160×290×80 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 160 mm bore, 290 mm OD, 80 mm width (6.299×11.417×3.150 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 19 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 160×290×80?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 160×290×80 mm in inches?

160×290×80 mm converts to 6.299×11.417×3.150 in, with a 65 mm (2.559 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22232, 22232-CCK-W33, 22232EAD1 mount in the same space despite different internal designs.