22232EMKD1 bearing: complete specifications & equivalents
The 22232EMKD1 is a ISO 15 radial bearing sized 160 x 290 x 80 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 160 mm |
| Outer diameter D | 290 mm |
| Width B | 80 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 1220 kN |
| Basic static load rating C0 | 1390 kN |
| Fatigue load limit Pu | 84.1 kN |
| Limiting speed (mechanical) | 1700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 22400 g |
| Manufacturer designation | NTN 22232EMKD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 22200-series range
| Bore d | 6.299 in |
|---|---|
| Outer diameter D | 11.417 in |
| Width B | 3.15 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 65 mm |
| Smallest bore in 22200-series | 25 mm |
| Largest outer diameter in 22200-series | 580 mm |
| Width range across 22200-series | 18–150 mm |
| Bore position in 22200-series (smallest first) | 22 of 32 |
| Bore above smallest 22200-series size | 135 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22232EMD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 22200-series envelope, cage and ratings; this is the tapered-bore execution (K, 1:12) of the cylindrical-bore 22232EMD1 — mounting (adapter/withdrawal sleeve or tapered seat, drive-up) differs. Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22232EMKD1 model number is decoded
The NTN order number 22232EMKD1 identifies a 160×290×80 mm (6.299 × 11.417 × 3.15 in) spherical roller bearing, 1:12 tapered bore (K), to the ISO 15 boundary plan. Digit by digit the code reads as spherical-roller dimension series plus 160 mm bore; the 80 mm width is the wide ISO 15 section, which is why spherical rollers interchange dimensionally but not in cage or rating detail. The 1:12 tapered bore mounts on an adapter/withdrawal sleeve (or tapered seat); drive-up sets the residual radial clearance and fixes the axial position of the 160 mm bore assembly. Speed planning: 1,700 r/min grease limiting speed is the cage/kinematic ceiling and 2,100 r/min is the oil-lubricated value for the 160 mm bore; vibrating screens rarely approach either and are load/cage limited instead. Check the self-aligning movement after fitting: the housing should pivot freely around the sphered outer raceway; a pinched outer ring removes the alignment capacity the bearing was selected for.
Typical equipment & failure modes
Common applications
- mining shovel and dragline swing shafts
- cement-rotary-kiln support and trunnion rolls
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- cage damage when a mounting force is applied through the roller set instead of the ring face
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- rolling-contact fatigue after the catalogue L10 life at the actual load
- false brinelling on stopped machines exposed to screen or crusher vibration
Selection pitfalls — read before you substitute
- At 160 mm bore 22232EMKD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Do not confuse EA and EM at the same number: 22232EMKD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 160×290 mm envelope is identical.
- Do not confuse EA and EM at the same number: 22232EMKD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 160×290 mm envelope is identical.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 160 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K seats.
- Do not confuse EA and EM at the same number: 22232EMKD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 160×290 mm envelope is identical.
- The 1220/1390 kN ratings, 84.1 kN Pu and 22400 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 22232EMKD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 22232EMKD1?
22232EMKD1 is an NTN double-row spherical roller bearing to ISO 15: 160 mm bore, 290 mm OD and 80 mm width (6.299 × 11.417 × 3.15 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 1220 kN, C0 1390 kN, Pu 84.1 kN, grease limiting speed 1,700 r/min, oil 2,100 r/min, mass about 22400 g. It is open, with one-piece machined brass cage (EM high-capacity design) and a 1:12 tapered bore.
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
K denotes a 1:12 tapered bore. 22232EMKD1 mounts on an adapter sleeve (or tapered shaft seat) and is driven up to the specified residual clearance; its cylindrical-bore counterpart in the same envelope and ratings is 22232EMD1.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 22232EMKD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 22232EMKD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 22232EMKD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 22232EMKD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 22200 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 1220 kN C / 1390 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.