22336EMKD1 bearing: complete specifications & equivalents
The 22336EMKD1 is a ISO 15 radial bearing sized 180 x 380 x 126 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 180 mm |
| Outer diameter D | 380 mm |
| Width B | 126 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 2420 kN |
| Basic static load rating C0 | 2810 kN |
| Fatigue load limit Pu | 132 kN |
| Limiting speed (mechanical) | 1100 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 68700 g |
| Manufacturer designation | NTN 22336EMKD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 22300-series range
| Bore d | 7.087 in |
|---|---|
| Outer diameter D | 14.961 in |
| Width B | 4.961 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 100 mm |
| Smallest bore in 22300-series | 40 mm |
| Largest outer diameter in 22300-series | 620 mm |
| Width range across 22300-series | 33–185 mm |
| Bore position in 22300-series (smallest first) | 21 of 28 |
| Bore above smallest 22300-series size | 140 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 22336EMD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 22300-series envelope, cage and ratings; this is the tapered-bore execution (K, 1:12) of the cylindrical-bore 22336EMD1 — mounting (adapter/withdrawal sleeve or tapered seat, drive-up) differs. Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 22336EMKD1 model number is decoded
The NTN order number 22336EMKD1 identifies a 180×380×126 mm (7.087 × 14.961 × 4.961 in) spherical roller bearing, 1:12 tapered bore (K), to the ISO 15 boundary plan. Reading the full code: the number gives the 180×380 mm envelope, EM names the cage/capacity execution, K marks the 1:12 tapered bore for adapter/withdrawal-sleeve mounting, and D1 outer-ring annular oil groove with holes completes the order number. At 2420 kN C and 68700 g mass the 22300 series part is built for shock and vibration; the 126 mm-wide ring needs square abutments to keep both rows equally loaded. 180 mm bore is 7.087 in and 380 mm OD is 14.961 in; the ISO 15 envelope swaps between brands, but the 2420/2810 kN ratings and cage design are NTN 2203E values. Check the self-aligning movement after fitting: the housing should pivot freely around the sphered outer raceway; a pinched outer ring removes the alignment capacity the bearing was selected for.
Typical equipment & failure modes
Common applications
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
- steel-mill and heavy crusher main shafts
- mining shovel and dragline swing shafts
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- cage damage when a mounting force is applied through the roller set instead of the ring face
- roller-end smearing during skidding starts under light load and high viscosity grease
- rolling-contact fatigue after the catalogue L10 life at the actual load
- brinelling from static overload or a hammer blow during sleeve mounting
Selection pitfalls — read before you substitute
- At 180 mm bore 22336EMKD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Never substitute 22336EMKD1 by envelope alone: the 2810 kN C0 and 132 kN Pu are specific to the NTN EM machined-brass-cage execution, and vibrating duty depends heavily on cage identity.
- Minimum load must be maintained even at rest under vibration: an unloaded 22336EMKD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- Never substitute 22336EMKD1 by envelope alone: the 2810 kN C0 and 132 kN Pu are specific to the NTN EM machined-brass-cage execution, and vibrating duty depends heavily on cage identity.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 1,100 r/min grease rating is lost to abrasive wear long before fatigue.
- The 2420/2810 kN ratings, 132 kN Pu and 68700 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 22336EMKD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 22336EMKD1?
22336EMKD1 is an NTN double-row spherical roller bearing to ISO 15: 180 mm bore, 380 mm OD and 126 mm width (7.087 × 14.961 × 4.961 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 2420 kN, C0 2810 kN, Pu 132 kN, grease limiting speed 1,100 r/min, oil 1,400 r/min, mass about 68700 g. It is open, with one-piece machined brass cage (EM high-capacity design) and a 1:12 tapered bore.
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
K denotes a 1:12 tapered bore. 22336EMKD1 mounts on an adapter sleeve (or tapered shaft seat) and is driven up to the specified residual clearance; its cylindrical-bore counterpart in the same envelope and ratings is 22336EMD1.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 22336EMKD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 22336EMKD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 22336EMKD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 22336EMKD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 22300 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 2420 kN C / 2810 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.