230-800B bearing: complete specifications & equivalents
The 230-800B is a ISO 15 radial bearing sized 800 x 1150 x 258 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 800 mm |
| Outer diameter D | 1150 mm |
| Width B | 258 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 9350 kN |
| Basic static load rating C0 | 19500 kN |
| Fatigue load limit Pu | 1340 kN |
| Limiting speed (mechanical) | 220 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 890000 g |
| Manufacturer designation | NTN 230/800B |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23000-series range
| Bore d | 31.496 in |
|---|---|
| Outer diameter D | 45.276 in |
| Width B | 10.157 in |
| ISO bore code | 30 |
| Radial section height (D−d)/2 | 175 mm |
| Smallest bore in 23000-series | 70 mm |
| Largest outer diameter in 23000-series | 1580 mm |
| Width range across 23000-series | 27–345 mm |
| Bore position in 23000-series (smallest first) | 40 of 46 |
| Bore above smallest 23000-series size | 730 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 230-800BK | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23000-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 230-800BK (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 230-800B model number is decoded
For heavy radial load with misalignment on a 800 mm shaft, NTN supplies 230/800B: sphered outer raceway, two roller rows, pressed-steel cage (standard execution), oil speed 290 r/min. The leading digits are the ISO 15 dimension series (23000 series); the bore code resolves to 800 mm (two-digit code ×5, with the 00–03 exception table), and 1150 mm OD / 258 mm width follow the general plan. Pu 1340 kN is the catalogue fatigue load limit for 230/800B, used in the adjusted-life equation at contaminated or partial-film conditions typical of mining and vibrating duty. Pu 1340 kN against C0 19500 kN anchors the contamination derating; for dirty mining duty the adjusted life of 230/800B moves with cleanliness far more than with small C variations. On vibrating-duty shafts verify the radial clearance class and cage choice at order time; the open 230/800B leaves sealing and the C3/C4 clearance decision to the application drawing.
Typical equipment & failure modes
Common applications
- cement-rotary-kiln support and trunnion rolls
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- pressed EA cage fatigue under sustained vibration when minimum load is not maintained
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- false brinelling on stopped machines exposed to screen or crusher vibration
- fretting corrosion between adapter sleeve and tapered bore when the drive-up is insufficient
Selection pitfalls — read before you substitute
- At 800 mm bore 230/800B is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 220 r/min grease rating is lost to abrasive wear long before fatigue.
- Oil relubrication toward 290 r/min needs drain and level design; flooding the 258 mm cavity churns heat through the heavy roller set and cage despite the higher oil speed figure.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 220 r/min grease rating is lost to abrasive wear long before fatigue.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a grooved 230/800B in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- The 9350/19500 kN ratings, 1340 kN Pu and 890000 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 230/800B (basic); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 230/800B?
230/800B is an NTN double-row spherical roller bearing to ISO 15: 800 mm bore, 1150 mm OD and 258 mm width (31.496 × 45.276 × 10.157 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 9350 kN, C0 19500 kN, Pu 1340 kN, grease limiting speed 220 r/min, oil 290 r/min, mass about 890000 g. It is open, with pressed-steel cage (standard execution).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
230/800B has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 230/800BK (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 230/800B is the basic execution.
What do D1 and W33 mean on 230/800B?
230/800B is listed without a D1/W33 outer-ring groove in 2203E; lubrication is supplied from the ring sides. D1 (NTN spelling) and W33 add the annular groove plus holes and are ordered as distinct suffixed executions of the same envelope.
How much misalignment and axial load can 230/800B take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23000 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 9350 kN C / 19500 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.