23030EMD1 bearing: complete specifications & equivalents
The 23030EMD1 is a ISO 15 radial bearing sized 150 x 225 x 56 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 150 mm |
| Outer diameter D | 225 mm |
| Width B | 56 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 660 kN |
| Basic static load rating C0 | 893 kN |
| Fatigue load limit Pu | 52.9 kN |
| Limiting speed (mechanical) | 2000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 7730 g |
| Manufacturer designation | NTN 23030EMD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23000-series range
| Bore d | 5.906 in |
|---|---|
| Outer diameter D | 8.858 in |
| Width B | 2.205 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 37.5 mm |
| Smallest bore in 23000-series | 70 mm |
| Largest outer diameter in 23000-series | 1580 mm |
| Width range across 23000-series | 27–345 mm |
| Bore position in 23000-series (smallest first) | 12 of 46 |
| Bore above smallest 23000-series size | 80 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23030EMKD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23000-series envelope, cage and ratings; this is the cylindrical-bore execution of the tapered-bore 23030EMKD1 (K/K30 sleeve or tapered-seat mounting). Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23030EMD1 model number is decoded
23030EMD1 is the EM machined-brass-cage execution of NTN's spherical roller range for a 150 mm shaft — 660 kN basic dynamic capacity in a 7730 g, open ISO 15 envelope. The leading digits are the ISO 15 dimension series (23000 series); the bore code resolves to 150 mm (two-digit code ×5, with the 00–03 exception table), and 225 mm OD / 56 mm width follow the general plan. Two symmetric roller rows share the load: C 660 kN, C0 893 kN (C0/C ≈ 1.35), with useful axial capacity in either direction alongside the dominant radial load. Catalogue mass 7730 g (7.73 kg) for the 150×225×56 mm execution includes the EM machined-brass-cage cage and both roller rows; shaft and housing shoulders must support that ring squarely. On vibrating-duty shafts verify the radial clearance class and cage choice at order time; the open 23030EMD1 leaves sealing and the C3/C4 clearance decision to the application drawing.
Typical equipment & failure modes
Common applications
- steel-mill and heavy crusher main shafts
- mining shovel and dragline swing shafts
- cement-rotary-kiln support and trunnion rolls
- large SAG/ball-mill trunnion and pinion shafts
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- cage damage when a mounting force is applied through the roller set instead of the ring face
- roller-end smearing during skidding starts under light load and high viscosity grease
- brinelling from static overload or a hammer blow during sleeve mounting
- water-induced pitting in washdown or outdoor duty without effective external seals
Selection pitfalls — read before you substitute
- At 150 mm bore 23030EMD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- K and K30 are different tapers — K is 1:12 and K30 is 1:30 on the wide series; an adapter sleeve for one will not mount the other 150 mm bearing, and drive-up procedures differ.
- Oil relubrication toward 2,500 r/min needs drain and level design; flooding the 56 mm cavity churns heat through the heavy roller set and cage despite the higher oil speed figure.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 56 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 150 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K seats.
- The 660/893 kN ratings, 52.9 kN Pu and 7730 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23030EMD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23030EMD1?
23030EMD1 is an NTN double-row spherical roller bearing to ISO 15: 150 mm bore, 225 mm OD and 56 mm width (5.906 × 8.858 × 2.205 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 660 kN, C0 893 kN, Pu 52.9 kN, grease limiting speed 2,000 r/min, oil 2,500 r/min, mass about 7730 g. It is open, with one-piece machined brass cage (EM high-capacity design).
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
23030EMD1 has a cylindrical bore and mounts directly on a machined shaft seat. Its tapered-bore counterpart is 23030EMKD1 (K = 1:12, or K30 = 1:30 on the wide series), intended for adapter/withdrawal-sleeve mounting.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23030EMD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 23030EMD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 23030EMD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 23030EMD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23000 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 660 kN C / 893 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.