150×225×56 mm bearings

16 models from 3 brands across 5 types share this ISO 15 envelope: 150 mm bore, 225 mm outside diameter, 56 mm width (5.906×8.858×2.205 in), 37.5 mm radial section.

16 models fit this space 3 brands 16 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
13030 Self-Aligning Ball SKF open CN 57.2 23.6 7500
23030 Spherical Roller SKF open CN 531 750 7950
23030-CCK-W33 Spherical Roller SKF open CN 531 750 11000
23030EAD1 Spherical Roller NTN open CN 660 893 7680
23030EAKD1 Spherical Roller NTN open CN 660 893 7450
23030EMD1 Spherical Roller NTN open CN 660 893 7730
23030EMKD1 Spherical Roller NTN open CN 660 893 7500
323030 Tapered Roller NTN open CN 395 630 7630
413030 Tapered Roller NTN open CN 305 430 6660
C3030-KV CARB Toroidal Roller SKF open CN 585 960 8000
C3030-MB CARB Toroidal Roller SKF open CN 540 850 8450
C3030-V CARB Toroidal Roller SKF open CN 585 960 8000
NCF3030-CV Cylindrical Roller SKF open CN 457 710 7500
NN3030 Cylindrical Roller NTN open CN 370 585 7810
NN3030K Cylindrical Roller NTN open CN 370 585 7530
SL183030 Cylindrical Roller FAG open CN 475 700 7330

Note: catalogue dynamic load ratings for this envelope span 57.2– 660.0 kN — a 1054% spread between designs in the very same 150×225×56 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 150 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 13030, 23030, 23030-CCK-W33, 23030EAD1, 23030EAKD1, 23030EMD1, 23030EMKD1, 323030, 413030, C3030-KV, C3030-MB, C3030-V, NCF3030-CV, NN3030, NN3030K, SL183030.

Frequently asked questions

Are all 150×225×56 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 150 mm bore, 225 mm OD, 56 mm width (5.906×8.858×2.205 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 16 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 150×225×56?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 150×225×56 mm in inches?

150×225×56 mm converts to 5.906×8.858×2.205 in, with a 37.5 mm (1.476 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 13030, 23030, 23030-CCK-W33 mount in the same space despite different internal designs.