23122EAKD1 bearing: complete specifications & equivalents
The 23122EAKD1 is a ISO 15 radial bearing sized 110 x 180 x 56 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 110 mm |
| Outer diameter D | 180 mm |
| Width B | 56 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 547 kN |
| Basic static load rating C0 | 669 kN |
| Fatigue load limit Pu | 36.2 kN |
| Limiting speed (mechanical) | 2200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 5490 g |
| Manufacturer designation | NTN 23122EAKD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23100-series range
| Bore d | 4.331 in |
|---|---|
| Outer diameter D | 7.087 in |
| Width B | 2.205 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 35 mm |
| Smallest bore in 23100-series | 100 mm |
| Largest outer diameter in 23100-series | 1420 mm |
| Width range across 23100-series | 52–412 mm |
| Bore position in 23100-series (smallest first) | 2 of 36 |
| Bore above smallest 23100-series size | 10 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23122EAD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23100-series envelope, cage and ratings; this is the tapered-bore execution (K, 1:12) of the cylindrical-bore 23122EAD1 — mounting (adapter/withdrawal sleeve or tapered seat, drive-up) differs. Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23122EAKD1 model number is decoded
23122EAKD1 is an NTN double-row spherical roller bearing: two rows of symmetric rollers on a sphered outer raceway, 110×180×56 mm to ISO 15, with pressed sheet-steel window cage (EA high-capacity design). On the NTN nameplate the suffix cluster after the size reads in order: cage design (EA), bore (K), lubrication feature (D1); 23122EAKD1 is assembled exactly in that order. The sphered outer raceway lets the inner-ring assembly pivot, accommodating shaft deflection and housing misalignment (around 1–2° for this class; use the 2203E value for the exact series) without edge loading the rollers. Selection: the C0/C ratio of 1.22 (669/547 kN) reflects the heavy static and shock proportioning of 23122EAKD1; size the equivalent load at the required L10 with shock factor for the application. Check the self-aligning movement after fitting: the housing should pivot freely around the sphered outer raceway; a pinched outer ring removes the alignment capacity the bearing was selected for.
Typical equipment & failure modes
Common applications
- large gearbox and marine gear shafts
- wind-turbine gearbox and rotor bearings
- large vibrating screens and mining feeders
- heavy conveyor and bucket-excavator pulleys
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- cage damage when a mounting force is applied through the roller set instead of the ring face
- roller-end smearing during skidding starts under light load and high viscosity grease
- brinelling from static overload or a hammer blow during sleeve mounting
- hard-particle indentation through the open arrangement in dusty mining duty
Selection pitfalls — read before you substitute
- Mount the 110 mm ring with induction heat or the sleeve drive-up procedure; at 5490 g cocking damages the spherical raceways, and repositioning after seating is impractical.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a D1 23122EAKD1 in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- Oil relubrication toward 2,800 r/min needs drain and level design; flooding the 56 mm cavity churns heat through the heavy roller set and cage despite the higher oil speed figure.
- Never substitute 23122EAKD1 by envelope alone: the 669 kN C0 and 36.2 kN Pu are specific to the NTN EA pressed-steel-cage execution, and vibrating duty depends heavily on cage identity.
- Minimum load must be maintained even at rest under vibration: an unloaded 23122EAKD1 on a stopped screen false-brinells; parking brakes and shaker isolation both matter.
- The 547/669 kN ratings, 36.2 kN Pu and 5490 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23122EAKD1 (EA pressed-steel-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23122EAKD1?
23122EAKD1 is an NTN double-row spherical roller bearing to ISO 15: 110 mm bore, 180 mm OD and 56 mm width (4.331 × 7.087 × 2.205 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 547 kN, C0 669 kN, Pu 36.2 kN, grease limiting speed 2,200 r/min, oil 2,800 r/min, mass about 5490 g. It is open, with pressed sheet-steel window cage (EA high-capacity design) and a 1:12 tapered bore.
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
K denotes a 1:12 tapered bore. 23122EAKD1 mounts on an adapter sleeve (or tapered shaft seat) and is driven up to the specified residual clearance; its cylindrical-bore counterpart in the same envelope and ratings is 23122EAD1.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23122EAKD1 is the EA pressed-steel-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 23122EAKD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 23122EAKD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 23122EAKD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23100 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 547 kN C / 669 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.