23126EMKD1 bearing: complete specifications & equivalents
The 23126EMKD1 is a ISO 15 radial bearing sized 130 x 210 x 64 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 130 mm |
| Outer diameter D | 210 mm |
| Width B | 64 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 710 kN |
| Basic static load rating C0 | 906 kN |
| Fatigue load limit Pu | 47.1 kN |
| Limiting speed (mechanical) | 1900 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 8250 g |
| Manufacturer designation | NTN 23126EMKD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23100-series range
| Bore d | 5.118 in |
|---|---|
| Outer diameter D | 8.268 in |
| Width B | 2.52 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 40 mm |
| Smallest bore in 23100-series | 100 mm |
| Largest outer diameter in 23100-series | 1420 mm |
| Width range across 23100-series | 52–412 mm |
| Bore position in 23100-series (smallest first) | 4 of 36 |
| Bore above smallest 23100-series size | 30 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23126EMD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23100-series envelope, cage and ratings; this is the tapered-bore execution (K, 1:12) of the cylindrical-bore 23126EMD1 — mounting (adapter/withdrawal sleeve or tapered seat, drive-up) differs. Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23126EMKD1 model number is decoded
NTN lists 23126EMKD1 with a 1:12 tapered bore (K) and D1 outer-ring annular oil groove with holes: 130 mm bore, 210 mm OD, 64 mm width, rated 1,900 r/min on grease. The leading digits are the ISO 15 dimension series (23100 series); the bore code resolves to 130 mm (two-digit code ×5, with the 00–03 exception table), and 210 mm OD / 64 mm width follow the general plan. Suffix reading on 23126EMKD1: EM identifies the high-capacity execution with a one-piece machined brass cage; K marks the 1:12 tapered bore; the ＊ symbol in 2203E marks the ULTAGE new-generation specification (not part of the order code); and D1 provides the outer-ring lubrication feature; quote the full code because each suffix is a distinct article. Grease/oil ratio: the 1,900 r/min limiting value is .79 of the 2,400 r/min oil value; heavy 64 mm-wide cages run hot in churning grease, so quantity and groove supply both matter. Fillet radii on shaft and housing must clear the ring chamfers of the 64 mm-wide set; use the NTN shoulder/withdrawal-groove table rather than copying a ball-bearing layout.
Typical equipment & failure modes
Common applications
- large SAG/ball-mill trunnion and pinion shafts
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- brinelling from static overload or a hammer blow during sleeve mounting
- rolling-contact fatigue after the catalogue L10 life at the actual load
Selection pitfalls — read before you substitute
- At 130 mm bore 23126EMKD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- K and K30 are different tapers — K is 1:12 and K30 is 1:30 on the wide series; an adapter sleeve for one will not mount the other 130 mm bearing, and drive-up procedures differ.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a D1 23126EMKD1 in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- Open spherical rollers swallow dust in mining duty; specify labyrinth or taconite seals externally, or the 1,900 r/min grease rating is lost to abrasive wear long before fatigue.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 64 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- The 710/906 kN ratings, 47.1 kN Pu and 8250 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23126EMKD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23126EMKD1?
23126EMKD1 is an NTN double-row spherical roller bearing to ISO 15: 130 mm bore, 210 mm OD and 64 mm width (5.118 × 8.268 × 2.52 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 710 kN, C0 906 kN, Pu 47.1 kN, grease limiting speed 1,900 r/min, oil 2,400 r/min, mass about 8250 g. It is open, with one-piece machined brass cage (EM high-capacity design) and a 1:12 tapered bore.
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
K denotes a 1:12 tapered bore. 23126EMKD1 mounts on an adapter sleeve (or tapered shaft seat) and is driven up to the specified residual clearance; its cylindrical-bore counterpart in the same envelope and ratings is 23126EMD1.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23126EMKD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 23126EMKD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 23126EMKD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 23126EMKD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23100 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 710 kN C / 906 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.