23134EMKD1 bearing: complete specifications & equivalents
The 23134EMKD1 is a ISO 15 radial bearing sized 170 x 280 x 88 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 170 mm |
| Outer diameter D | 280 mm |
| Width B | 88 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 1270 kN |
| Basic static load rating C0 | 1700 kN |
| Fatigue load limit Pu | 77.3 kN |
| Limiting speed (mechanical) | 1400 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 20900 g |
| Manufacturer designation | NTN 23134EMKD1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 23100-series range
| Bore d | 6.693 in |
|---|---|
| Outer diameter D | 11.024 in |
| Width B | 3.465 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 55 mm |
| Smallest bore in 23100-series | 100 mm |
| Largest outer diameter in 23100-series | 1420 mm |
| Width range across 23100-series | 52–412 mm |
| Bore position in 23100-series (smallest first) | 8 of 36 |
| Bore above smallest 23100-series size | 70 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23134EMD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 23100-series envelope, cage and ratings; this is the tapered-bore execution (K, 1:12) of the cylindrical-bore 23134EMD1 — mounting (adapter/withdrawal sleeve or tapered seat, drive-up) differs. Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23134EMKD1 model number is decoded
23134EMKD1 is the EM machined-brass-cage execution of NTN's spherical roller range for a 170 mm shaft — 1270 kN basic dynamic capacity in a 20900 g, open ISO 15 envelope. Reading the full code: the number gives the 170×280 mm envelope, EM names the cage/capacity execution, K marks the 1:12 tapered bore for adapter/withdrawal-sleeve mounting, and D1 outer-ring annular oil groove with holes completes the order number. Pu 77.3 kN is the catalogue fatigue load limit for 23134EMKD1, used in the adjusted-life equation at contaminated or partial-film conditions typical of mining and vibrating duty. Selection: the C0/C ratio of 1.34 (1700/1270 kN) reflects the heavy static and shock proportioning of 23134EMKD1; size the equivalent load at the required L10 with shock factor for the application. Fillet radii on shaft and housing must clear the ring chamfers of the 88 mm-wide set; use the NTN shoulder/withdrawal-groove table rather than copying a ball-bearing layout.
Typical equipment & failure modes
Common applications
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
- steel-mill and heavy crusher main shafts
Known failure patterns
- lubricant starvation at the centre rib area when the D1/W33 groove is not connected to a relubrication supply
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- roller-end smearing during skidding starts under light load and high viscosity grease
- false brinelling on stopped machines exposed to screen or crusher vibration
- false brinelling on stopped machines exposed to screen or crusher vibration
Selection pitfalls — read before you substitute
- At 170 mm bore 23134EMKD1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- Do not confuse EA and EM at the same number: 23134EMKD1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 170×280 mm envelope is identical.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a D1 23134EMKD1 in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- Adapter-sleeve mounting requires the correct sleeve series and locknut for the 170 mm shaft; a sleeve sized to bore alone ignores thread, width and the oil-injection option on large K seats.
- The D1/W33 groove only helps if the housing has a matching grease passage; mounting a D1 23134EMKD1 in a solid block with no port wastes the feature and leaves the centre rows under-lubricated.
- The 1270/1700 kN ratings, 77.3 kN Pu and 20900 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 23134EMKD1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 23134EMKD1?
23134EMKD1 is an NTN double-row spherical roller bearing to ISO 15: 170 mm bore, 280 mm OD and 88 mm width (6.693 × 11.024 × 3.465 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 1270 kN, C0 1700 kN, Pu 77.3 kN, grease limiting speed 1,400 r/min, oil 1,800 r/min, mass about 20900 g. It is open, with one-piece machined brass cage (EM high-capacity design) and a 1:12 tapered bore.
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
K denotes a 1:12 tapered bore. 23134EMKD1 mounts on an adapter sleeve (or tapered shaft seat) and is driven up to the specified residual clearance; its cylindrical-bore counterpart in the same envelope and ratings is 23134EMD1.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 23134EMKD1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 23134EMKD1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 23134EMKD1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 23134EMKD1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 23100 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 1270 kN C / 1700 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.