23252 bearing: complete specifications & equivalents
The 23252 is a ISO 15 radial bearing sized 260 x 480 x 174 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 260 mm |
| Outer diameter D | 480 mm |
| Width B | 174 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 3395 kN |
| Basic static load rating C0 | 4750 kN |
| Fatigue load limit Pu | 360 kN |
| Reference speed (thermal) | 850 rpm |
| Limiting speed (mechanical) | 1200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 140000 g |
| Manufacturer designation | SKF 23252 CC/W33 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings |
| Last verified | 2026-09-26 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings) · extracted 2026-09-26
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 23200-series range
| Bore d | 10.236 in |
|---|---|
| Outer diameter D | 18.898 in |
| Width B | 6.85 in |
| ISO bore code | 52 |
| Radial section height (D−d)/2 | 110 mm |
| Smallest bore in 23200-series | 90 mm |
| Largest outer diameter in 23200-series | 870 mm |
| Width range across 23200-series | 52.4–310 mm |
| Bore position in 23200-series (smallest first) | 15 of 26 |
| Bore above smallest 23200-series size | 170 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 23252 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; D/B cross-verified against Schaeffler HR1 2022; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
| 23252-CCK-W33 | SKF | full Dimensions and internal design equivalent — standard interchange. | Tapered-bore (1:12) execution on OH2352 adapter sleeve; same ISO 15 envelope, separate order number. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 23252 model number is decoded
23252 CC/W33 belongs to the SKF spherical roller range — the 260 mm bore entry in the 23200-series series (dimension series 32 (medium OD, extra wide)), dimensioned 480 mm OD and 174 mm wide. On the SKF nameplate, 23252 follows the ISO 15 convention: 2 for the spherical roller type, 32 for the dimension series 32 (medium OD, extra wide), final digits 52 for the 260 mm bore. In SKF suffix language, E marks the optimized high-capacity design and CC/W33 the pressed-steel-cage execution with relubrication groove; both are open bearings — the sealed variant carries the 2CS5 suffix and the vibrating-screen execution VA405. With C 3395 kN and C0 4750 kN, the 23252 load check covers radial plus moderate axial in either direction — but below the minimum load the rollers skid, so verify P ≥ 0.01·C0 at the lightest operating point. The cylindrical-bore execution here seats directly on the shaft journal; if the application calls for an adapter sleeve, order the tapered-bore 23252 CCK/W33 variant instead and measure the drive-up or clearance reduction, not the nut torque.
Typical equipment & failure modes
Common applications
- heavy rolling-mill work-roll chocks
- large dredger and marine winch drums
- steel-plant continuous-caster segments
- large induced-draft fan rotors
Known failure patterns
- raceway fatigue spalling of the sphered outer raceway after extended service above the catalogue L10 rating
- inner-ring raceway spalling from edge loading when misalignment exceeds the self-aligning recovery range
- cage pocket wear or fracture from roller skew at insufficient minimum load or rapid acceleration
- surface distress and smearing when the relubrication interval is exceeded — the W33 groove is only effective if grease actually reaches the roller rows
- seal-lip wear and grease purge loss when an open bearing is run without functioning housing seals
Selection pitfalls — read before you substitute
- At 260 mm bore the ring mass makes cocking during mounting a real risk; guide the bearing square, confirm seat contact around the full circumference, and re-check the self-aligning swing after the housing cap is torqued down.
- The 23200-series series at 260 mm bore (480×174 mm) adds still more width for shock-loaded and vibratory loads; it does not interchange with a 231 bearing of the same bore because the 174 mm width changes abutment spacing, even though the 480 mm OD matches.
- Shaft and housing fillets must clear the bearing chamfer so the 174 mm-wide rings seat square; use an undercut or withdrawal groove rather than an oversized radius that locks on the ring face.
- Shaft and housing fillets must clear the bearing chamfer so the 174 mm-wide rings seat square; use an undercut or withdrawal groove rather than an oversized radius that locks on the ring face.
- The 3395/4750 kN ratings are SKF catalogue values for this exact execution (23252 CC/W33); SKF can revise internal geometry without changing the order number, so keep the catalogue version (SKF catalogue PUB BU/P1 17000) with the specification and re-verify for critical drives.
- SKF lists several executions of 23252 (cylindrical bore as listed, tapered-bore 23252 CCK/W33 variant, plus sealed and vibrating-screen options in the same envelope); they are not interchangeable order numbers — quote the full 23252 CC/W33 designation when purchasing.
Frequently asked questions
What are the dimensions and catalogue data of 23252?
The 23252 CC/W33 is a double-row spherical roller bearing with 260 mm bore, 480 mm outer diameter and 174 mm width (10.236 × 18.898 × 6.85 in) per ISO 15. From SKF catalogue PUB BU/P1 17000: basic dynamic load rating C 3395 kN, C0 4750 kN, fatigue load limit Pu 360 kN, reference speed 850 r/min, limiting speed 1,200 r/min, mass about 140000 g. It is an open, self-aligning bearing with two pressed-steel cages with a floating guide ring.
How does the 23252 bore code work?
The last two digits of 23252 are bore code 52, so 52 × 5 = 260 mm bore. The 480 mm OD and 174 mm width come from the ISO 15 dimension-series plan (dimension series 32 (medium OD, extra wide)), shared with other spherical roller bearings of the same code.
What does the CC/W33 suffix mean on 23252?
CC denotes two pressed-steel cages with a floating guide ring between the roller rows, and W33 adds an annular groove plus three lubrication holes in the outer ring for relubrication. CCK/W33 is the 1:12 tapered-bore counterpart.
Can 23252 accommodate misalignment and axial load?
Yes on both counts. The sphered outer raceway lets the bearing self-align ≈ 0.5–2.5° depending on series, absorbing shaft deflection and housing-seat errors. The two barrel-roller rows also carry bidirectional axial load in addition to heavy radial load — this is the key difference from cylindrical roller bearings, which take no axial load.
When should the tapered-bore 23252K variant be used instead?
Choose the K (1:12 tapered bore) variant when the bearing must seat on an adapter or withdrawal sleeve — typical for long shafts, frequent dismounting, or stepped shafts where machining a precision journal is impractical. Sleeve mounting requires measuring clearance reduction or axial drive-up, not nut torque. The cylindrical-bore 23252 listed here seats directly on a machined journal.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 9.1 spherical roller bearings on 2026-09-26. Read our editorial & correction policy.