24030EMK30D1 bearing: complete specifications & equivalents
The 24030EMK30D1 is a ISO 15 radial bearing sized 150 x 225 x 75 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 150 mm |
| Outer diameter D | 225 mm |
| Width B | 75 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | brass, machined (M1) |
| Basic dynamic load rating C | 789 kN |
| Basic static load rating C0 | 1140 kN |
| Fatigue load limit Pu | 51.2 kN |
| Limiting speed (mechanical) | 1700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 10300 g |
| Manufacturer designation | NTN 24030EMK30D1 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 24000-series range
| Bore d | 5.906 in |
|---|---|
| Outer diameter D | 8.858 in |
| Width B | 2.953 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 37.5 mm |
| Smallest bore in 24000-series | 65 mm |
| Largest outer diameter in 24000-series | 1580 mm |
| Width range across 24000-series | 35–462 mm |
| Bore position in 24000-series (smallest first) | 8 of 42 |
| Bore above smallest 24000-series size | 85 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 24030EMD1 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same NTN 24000-series envelope, cage and ratings; this is the tapered-bore execution (K30, 1:30) of the cylindrical-bore 24030EMD1 — mounting (adapter/withdrawal sleeve or tapered seat, drive-up) differs. Verify shaft arrangement. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 24030EMK30D1 model number is decoded
24030EMK30D1 is the EM machined-brass-cage execution of NTN's spherical roller range for a 150 mm shaft — 789 kN basic dynamic capacity in a 10300 g, open ISO 15 envelope. Reading the full code: the number gives the 150×225 mm envelope, EM names the cage/capacity execution, K30 marks the 1:30 tapered bore for sleeve mounting, and D1 outer-ring annular oil groove with holes completes the order number. Open by design, 24030EMK30D1 requires application seals and a grease or oil system; NTN vibrating-duty executions of this envelope are selected with cage and clearance choices that are separate order codes. Catalogue mass 10300 g (10.30 kg) for the 150×225×75 mm execution includes the EM machined-brass-cage cage and both roller rows; shaft and housing shoulders must support that ring squarely. Fillet radii on shaft and housing must clear the ring chamfers of the 75 mm-wide set; use the NTN shoulder/withdrawal-groove table rather than copying a ball-bearing layout.
Typical equipment & failure modes
Common applications
- heavy vibrating screens and grizzly feeders
- offshore and marine propulsion shaftlines
- large wind-turbine main-shaft arrangements
- steel-mill and heavy crusher main shafts
Known failure patterns
- raceway spalling at the roller ends when misalignment or deflection concentrates the line contact
- machined EM cage wear from inadequate oil film at the cage-guiding surfaces
- sliding wear and heat when relubrication intervals ignore the groove (D1/W33) supply path
- false brinelling on stopped machines exposed to screen or crusher vibration
- false brinelling on stopped machines exposed to screen or crusher vibration
Selection pitfalls — read before you substitute
- At 150 mm bore 24030EMK30D1 is normally mounted on adapter/withdrawal sleeves with hydraulic assistance; follow the NTN drive-up angle or oil-injection procedure — manual nut tightening cannot set the multi-tonne seating correctly.
- The two roller rows must share load equally — a tilted spacer or unequal abutment on the 75 mm-wide ring loads one row only and shows as asymmetric race polish during inspection.
- Do not confuse EA and EM at the same number: 24030EMK30D1 carries EM machined-brass-cage; swapping to the other cage execution changes mass, speed behaviour and sometimes suitability for vibration, even though the 150×225 mm envelope is identical.
- Self-aligning does not mean unlimited misalignment: beyond the catalogue angle the outer ring's spherical travel is exhausted and the 789 kN rating no longer applies.
- Self-aligning does not mean unlimited misalignment: beyond the catalogue angle the outer ring's spherical travel is exhausted and the 789 kN rating no longer applies.
- The 789/1140 kN ratings, 51.2 kN Pu and 10300 g mass are NTN Ball and Roller Bearings CAT.No.2203E values for 24030EMK30D1 (EM machined-brass-cage/D1); another maker's same-envelope part revises internal geometry, so re-verify ratings and cage before substitution on vibrating or rated drives.
Frequently asked questions
What are the dimensions and catalogue data of 24030EMK30D1?
24030EMK30D1 is an NTN double-row spherical roller bearing to ISO 15: 150 mm bore, 225 mm OD and 75 mm width (5.906 × 8.858 × 2.953 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 789 kN, C0 1140 kN, Pu 51.2 kN, grease limiting speed 1,700 r/min, oil 2,100 r/min, mass about 10300 g. It is open, with one-piece machined brass cage (EM high-capacity design) and a 1:30 tapered bore.
What is the difference between the K/K30 tapered bore and the cylindrical bore versions?
K30 denotes a 1:30 tapered bore (the wide 24000 series). 24030EMK30D1 mounts on a matching adapter or withdrawal sleeve on a plain 150 mm shaft and is driven up to a measured radial clearance; the cylindrical-bore counterpart is 24030EMD1.
What do EA and EM mean on NTN spherical roller bearings?
EA is the NTN standard-capacity/high-capacity execution with a pressed sheet-steel window cage; EM is the high-capacity execution with a one-piece machined brass cage. Both use the optimised symmetric-roller design, but cage identity changes mass, speed behaviour and suitability for duties like vibrating screens, so they are separate order numbers. 24030EMK30D1 is the EM machined-brass-cage execution, listed with the ＊ ULTAGE new-generation mark.
What do D1 and W33 mean on 24030EMK30D1?
D1 is NTN's outer-ring lubrication feature: an annular groove with oil holes around the outer ring, aligned with a housing grease port so lubricant reaches both roller rows directly. 24030EMK30D1 carries D1; W33 is the equivalent industry-spelled annular-groove-and-holes feature seen on other executions.
How much misalignment and axial load can 24030EMK30D1 take?
The sphered outer raceway compensates static and dynamic misalignment in the order of 1–2° (verify the exact 2203E figure for the 24000 series); beyond that, load concentrates on one roller row. Load is predominantly radial with a moderate axial share in either direction — 789 kN C / 1140 kN C0 — but sustained pure axial load is not recommended because it unloads one row.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.