413034 bearing: complete specifications & equivalents
The 413034 is a ANSI ABMA 19.2 radial bearing sized 170 x 260 x 67 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 170 mm |
| Outer diameter D | 260 mm |
| Width B | 67 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 405 kN |
| Basic static load rating C0 | 620 kN |
| Fatigue load limit Pu | 60 kN |
| Limiting speed (mechanical) | 1100 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 11600 g |
| Manufacturer designation | NTN 4T-413034 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 6.693 in |
|---|---|
| Outer diameter D | 10.236 in |
| Width B | 2.638 in |
| ISO bore code | 34 |
| Radial section height (D−d)/2 | 45 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 21 of 41 |
| Bore above smallest 4t-430-series size | 130 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 413034 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 413034 model number is decoded
For a 170 mm shaft needing a compact two-direction thrust location, NTN lists 4T-413034, a TDO double-row 4T unit of 405 kN C and 620 kN C0 in the light-duty 430-family TDO double-row series. Unlike a pair of single-row bearings, the TDO unit of 4T-413034 integrates both rows in one article: the 67 mm overall width and the internal clearance are ground and set by NTN, so there is no field adjustment dimension. Grease relubrication at the 1,100 r/min limiting speed must reach both roller rows; sustaining 1,400 r/min needs an oil supply with defined flow through the double cup. Because the unit is preset, mounting 4T-413034 resembles mounting a double-row spherical or cylindrical bearing: seat the unit, clamp axially to the stated end cover torque, and verify rotation — no end-play measurement is required. The open unit carries no seals; the housing of 4T-413034 must provide sealing and the grease fill or oil feed to both rows.
Typical equipment & failure modes
Common applications
- heavy press and forging-machine drives
- large shredder and recycler main shafts
- power-plant mill and fan shafts
- rolling-mill roll-neck and pinion-stand positions
Known failure patterns
- roller large-end smearing against the cone ribs when one row of the unit runs starved of lubricant
- one-row flaking when a bent shaft concentrates the combined load on a single row of the pair
- overheated running after a field attempt to "tighten up" the factory-set internal clearance
- cage damage when the unit is lifted by one cone instead of the double cup during fitting
- thermal distress when the oil supply sized for one row starves the second row
Selection pitfalls — read before you substitute
- At 170 mm bore the 4T-413034 unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 405 kN C level.
- The 430 light plan keeps 4T-413034 narrower and faster than the 432 heavy execution of the same 170 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- Never interchange a TDO double-row unit with two single-row bearings of similar size: the 67 mm width, load spread and clearance logic of 4T-413034 are unit-specific.
- Open 4T-413034 units have no seals: the housing must seal both rows or the 1,100 r/min grease figure is meaningless once contamination enters.
- An unloaded 4T-413034 near 1,100 r/min lets rollers skid; ensure a minimum load or light spring preload on high-speed positions.
- The 405/620 kN ratings and 60 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-413034; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-413034?
4T-413034 is a double-row tapered roller bearing of TDO (back-to-back) construction: 170 mm bore, 260 mm outside diameter and 67 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 405 kN, C0 620 kN, Cu 60 kN, grease limiting speed 1,100 r/min, oil speed 1,400 r/min, mass about 11.6 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 170 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-413034 belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-413034 be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 67 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 413034 mean?
With no letter suffix, 413034 is the basic open double-row execution: steel cages, factory-set internal clearance, no feature suffix in the order code.
Why does 4T-413034 list two speeds, 1,100 and 1,400 r/min?
The lower figure, 1,100 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-413034 at 1,400 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.