423028 bearing: complete specifications & equivalents
The 423028 is a ANSI ABMA 19.2 radial bearing sized 140 x 210 x 66 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 140 mm |
| Outer diameter D | 210 mm |
| Width B | 66 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 335 kN |
| Basic static load rating C0 | 535 kN |
| Fatigue load limit Pu | 55 kN |
| Limiting speed (mechanical) | 1300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 7070 g |
| Manufacturer designation | NTN 4T-423028 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 5.512 in |
|---|---|
| Outer diameter D | 8.268 in |
| Width B | 2.598 in |
| ISO bore code | 28 |
| Radial section height (D−d)/2 | 35 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 18 of 41 |
| Bore above smallest 4t-430-series size | 100 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 423028 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 423028 model number is decoded
For a 140 mm shaft needing a compact two-direction thrust location, NTN lists 4T-423028, a TDO double-row 4T unit of 335 kN C and 535 kN C0 in the light-duty 430-family TDO double-row series. Reading the designation: the last two digits 28 are the bore code, ×5 = 140 mm (codes 00–03 use the 10/12/15/17 exception table); the leading digits place the bearing in the light-duty 430-family TDO double-row series. Double-row capacity is not twice a single-row bearing: the printed 335 kN C already accounts for load sharing between the two rows of 4T-423028, so apply it directly in the L10 calculation. TDO construction means the two cone assemblies of 4T-423028 face away from each other inside one double cup: the load lines diverge outward, giving a wide effective spread and high moment stiffness for the 140 mm shaft. The open unit carries no seals; the housing of 4T-423028 must provide sealing and the grease fill or oil feed to both rows.
Typical equipment & failure modes
Common applications
- power-plant mill and fan shafts
- rolling-mill roll-neck and pinion-stand positions
- mine hoist and dragline drum shafts
- cement-plant mill and kiln drive trains
Known failure patterns
- roller large-end smearing against the cone ribs when one row of the unit runs starved of lubricant
- overheated running after a field attempt to "tighten up" the factory-set internal clearance
- one-row flaking when a bent shaft concentrates the combined load on a single row of the pair
- cage damage when the unit is lifted by one cone instead of the double cup during fitting
- false brinelling on a stored or standby unit exposed to vibration
Selection pitfalls — read before you substitute
- At 140 mm bore the 4T-423028 unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 335 kN C level.
- The 430 light plan keeps 4T-423028 narrower and faster than the 432 heavy execution of the same 140 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- At inspection do not mix the cone assemblies of 4T-423028 with another unit; rows are ground together and re-matching is not guaranteed in the field.
- The 335 kN C already includes two-row load sharing — do not double it when pairing the unit with a floating bearing in the L10 calculation.
- Lubricant must reach both rows: a housing groove aligned to the cup mid-width of 4T-423028 feeds the two roller complements evenly; a single-side feed starves the far row.
- The 335/535 kN ratings and 55 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-423028; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-423028?
4T-423028 is a double-row tapered roller bearing of TDO (back-to-back) construction: 140 mm bore, 210 mm outside diameter and 66 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 335 kN, C0 535 kN, Cu 55 kN, grease limiting speed 1,300 r/min, oil speed 1,800 r/min, mass about 7.07 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 140 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-423028 belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-423028 be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 66 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 423028 mean?
With no letter suffix, 423028 is the basic open double-row execution: steel cages, factory-set internal clearance, no feature suffix in the order code.
Why does 4T-423028 list two speeds, 1,300 and 1,800 r/min?
The lower figure, 1,300 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-423028 at 1,800 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.