423030 bearing: complete specifications & equivalents
The 423030 is a ANSI ABMA 19.2 radial bearing sized 150 x 225 x 70 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 150 mm |
| Outer diameter D | 225 mm |
| Width B | 70 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 395 kN |
| Basic static load rating C0 | 630 kN |
| Fatigue load limit Pu | 64 kN |
| Limiting speed (mechanical) | 1200 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 8480 g |
| Manufacturer designation | NTN 4T-423030 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 5.906 in |
|---|---|
| Outer diameter D | 8.858 in |
| Width B | 2.756 in |
| ISO bore code | 30 |
| Radial section height (D−d)/2 | 37.5 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 19 of 41 |
| Bore above smallest 4t-430-series size | 110 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 423030 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 423030 model number is decoded
4T-423030 is an NTN double-row tapered roller bearing of TDO (back-to-back) construction: two cone assemblies against one double cup, supplied as a preset unit of 150×225×70 mm. The 4T- prefix is NTN's tapered roller quality mark; 430 numbers the light TDO plan and 432 the heavy TDO plan — at the same 150 mm bore the 432 execution carries a wider, heavier section than the 430. The 2.6 kN of dynamic capacity per millimetre of bore summarises the 395 kN rating over the 150 mm bore — compare substitution candidates on this ratio and on the 70 mm width. TDO construction means the two cone assemblies of 4T-423030 face away from each other inside one double cup: the load lines diverge outward, giving a wide effective spread and high moment stiffness for the 150 mm shaft. Induction heating to max 120 °C is the standard fitting method at this 150 mm bore; driving the unit home through the rollers brinells both rows at once.
Typical equipment & failure modes
Common applications
- large shredder and recycler main shafts
- power-plant mill and fan shafts
- rolling-mill roll-neck and pinion-stand positions
- mine hoist and dragline drum shafts
Known failure patterns
- edge loading on one row when the housing seats the double cup cocked across its width
- brinelling of both rows from a mounting blow transmitted through the roller complements
- preload loss and hammering noise when the cup clamping loosens and the unit gains axial float
- cage fatigue after continuous running near the grease limiting speed without oil cooling
- false brinelling on a stored or standby unit exposed to vibration
Selection pitfalls — read before you substitute
- At 150 mm bore the 4T-423030 unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 395 kN C level.
- The 430 light plan keeps 4T-423030 narrower and faster than the 432 heavy execution of the same 150 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- Grease packs must leave free volume across the 70 mm width; over-greasing a unit churning near the 1,600 r/min oil-band speed raises temperature and expels the grease.
- At inspection do not mix the cone assemblies of 4T-423030 with another unit; rows are ground together and re-matching is not guaranteed in the field.
- Clamping the double cup with a cocked end cover pinches one row: tighten the 225 mm OD clamping uniformly around the circumference.
- The 395/630 kN ratings and 64 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-423030; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-423030?
4T-423030 is a double-row tapered roller bearing of TDO (back-to-back) construction: 150 mm bore, 225 mm outside diameter and 70 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 395 kN, C0 630 kN, Cu 64 kN, grease limiting speed 1,200 r/min, oil speed 1,600 r/min, mass about 8.48 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 150 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-423030 belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-423030 be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 70 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 423030 mean?
With no letter suffix, 423030 is the basic open double-row execution: steel cages, factory-set internal clearance, no feature suffix in the order code.
Why does 4T-423030 list two speeds, 1,200 and 1,600 r/min?
The lower figure, 1,200 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-423030 at 1,600 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.