430328X bearing: complete specifications & equivalents
The 430328X is a ANSI ABMA 19.2 radial bearing sized 140 x 300 x 145 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 140 mm |
| Outer diameter D | 300 mm |
| Width B | 145 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 1220 kN |
| Basic static load rating C0 | 1560 kN |
| Fatigue load limit Pu | 150 kN |
| Limiting speed (mechanical) | 1100 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 43200 g |
| Manufacturer designation | NTN 4T-430328X |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 5.512 in |
|---|---|
| Outer diameter D | 11.811 in |
| Width B | 5.709 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 80 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 18 of 41 |
| Bore above smallest 4t-430-series size | 100 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 430328X | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 430328X model number is decoded
The NTN 2203E double-row table prints 4T-430328X at 140 mm bore, 300 mm OD and 145 mm overall width, with a grease limiting speed of 1,100 r/min and an oil ceiling of 1,400 r/min. Reading the designation: the last two digits 28 are the bore code, ×5 = 140 mm (codes 00–03 use the 10/12/15/17 exception table); the leading digits place the bearing in the light-duty 430-family TDO double-row series. Catalogue mass of 4T-430328X is 43.2 kg; lifting and fitting tackle must be rated for the whole preset unit, not for single-ring handling. TDO construction means the two cone assemblies of 4T-430328X face away from each other inside one double cup: the load lines diverge outward, giving a wide effective spread and high moment stiffness for the 140 mm shaft. The open unit carries no seals; the housing of 4T-430328X must provide sealing and the grease fill or oil feed to both rows.
Typical equipment & failure modes
Common applications
- heavy press and forging-machine drives
- large shredder and recycler main shafts
- power-plant mill and fan shafts
- rolling-mill roll-neck and pinion-stand positions
Known failure patterns
- roller large-end smearing against the cone ribs when one row of the unit runs starved of lubricant
- brinelling of both rows from a mounting blow transmitted through the roller complements
- preload loss and hammering noise when the cup clamping loosens and the unit gains axial float
- pressed-steel cage pocket wear from roller skid at light load and high speed
- false brinelling on a stored or standby unit exposed to vibration
Selection pitfalls — read before you substitute
- At 140 mm bore the 4T-430328X unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 1220 kN C level.
- The 430 light plan keeps 4T-430328X narrower and faster than the 432 heavy execution of the same 140 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- Lubricant must reach both rows: a housing groove aligned to the cup mid-width of 4T-430328X feeds the two roller complements evenly; a single-side feed starves the far row.
- Clamping the double cup with a cocked end cover pinches one row: tighten the 300 mm OD clamping uniformly around the circumference.
- At inspection do not mix the cone assemblies of 4T-430328X with another unit; rows are ground together and re-matching is not guaranteed in the field.
- The 1220/1560 kN ratings and 150 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-430328X; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-430328X?
4T-430328X is a double-row tapered roller bearing of TDO (back-to-back) construction: 140 mm bore, 300 mm outside diameter and 145 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 1220 kN, C0 1560 kN, Cu 150 kN, grease limiting speed 1,100 r/min, oil speed 1,400 r/min, mass about 43.2 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 140 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-430328X belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-430328X be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 145 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 430328X mean?
Suffix reading on 430328X: X marks the boundary-dimension revision of the base number (D and width differ from the plain number of the same bore); suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-430328X list two speeds, 1,100 and 1,400 r/min?
The lower figure, 1,100 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-430328X at 1,400 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.