430328XUUTG bearing: complete specifications & equivalents
The 430328XUUTG is a ANSI ABMA 19.2 radial bearing sized 140 x 300 x 145 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 140 mm |
| Outer diameter D | 300 mm |
| Width B | 145 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 1620 kN |
| Basic static load rating C0 | 1900 kN |
| Fatigue load limit Pu | 183 kN |
| Limiting speed (mechanical) | 1100 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 45300 g |
| Manufacturer designation | NTN 4T-430328XUUTG |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-430-series range
| Bore d | 5.512 in |
|---|---|
| Outer diameter D | 11.811 in |
| Width B | 5.709 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 80 mm |
| Smallest bore in 4t-430-series | 40 mm |
| Largest outer diameter in 4t-430-series | 870 mm |
| Width range across 4t-430-series | 45–310 mm |
| Bore position in 4t-430-series (smallest first) | 18 of 41 |
| Bore above smallest 4t-430-series size | 100 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 430328XUUTG | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 430328XUUTG model number is decoded
For a 140 mm shaft needing a compact two-direction thrust location, NTN lists 4T-430328XUUTG, a TDO double-row 4T unit of 1620 kN C and 1900 kN C0 in the light-duty 430-family TDO double-row series. Large sizes continue the plans under different leading digits: 4130/4131 and 4230/4231 belong to the 430-family dimension plan, while 3230/3231 continue the 432 heavy plan — 430328XUUTG reads accordingly. Double-row capacity is not twice a single-row bearing: the printed 1620 kN C already accounts for load sharing between the two rows of 4T-430328XUUTG, so apply it directly in the L10 calculation. The internal clearance of 4T-430328XUUTG is set at the factory by the double cup and spacer-less grinding; do not attempt to re-adjust it with shaft nuts — the 145 mm overall width is the finished dimension. Re-lubrication holes and grooves of the housing should line up with the cup's mid-width so fresh grease reaches both roller rows of 4T-430328XUUTG.
Typical equipment & failure modes
Common applications
- heavy press and forging-machine drives
- large shredder and recycler main shafts
- power-plant mill and fan shafts
- rolling-mill roll-neck and pinion-stand positions
Known failure patterns
- edge loading on one row when the housing seats the double cup cocked across its width
- overheated running after a field attempt to "tighten up" the factory-set internal clearance
- one-row flaking when a bent shaft concentrates the combined load on a single row of the pair
- pressed-steel cage pocket wear from roller skid at light load and high speed
- indentation of both raceways by hard particles in an open, unsealed arrangement
Selection pitfalls — read before you substitute
- At 140 mm bore the 4T-430328XUUTG unit needs hydraulic or crane-assisted fitting and a verified oil supply; manual methods cannot control seating at the 1620 kN C level.
- The 430 light plan keeps 4T-430328XUUTG narrower and faster than the 432 heavy execution of the same 140 mm bore; where shock or a high thrust share dominates, verify whether the heavier 432-family row is the intended position.
- Never interchange a TDO double-row unit with two single-row bearings of similar size: the 145 mm width, load spread and clearance logic of 4T-430328XUUTG are unit-specific.
- Clamping the double cup with a cocked end cover pinches one row: tighten the 300 mm OD clamping uniformly around the circumference.
- Lubricant must reach both rows: a housing groove aligned to the cup mid-width of 4T-430328XUUTG feeds the two roller complements evenly; a single-side feed starves the far row.
- The 1620/1900 kN ratings and 183 kN Cu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-430328XUUTG; internal geometry legitimately differs between manufacturers, so re-verify ratings, clearance class and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-430328XUUTG?
4T-430328XUUTG is a double-row tapered roller bearing of TDO (back-to-back) construction: 140 mm bore, 300 mm outside diameter and 145 mm overall width. From NTN Ball and Roller Bearings CAT.No.2203E: C 1620 kN, C0 1900 kN, Cu 183 kN, grease limiting speed 1,100 r/min, oil speed 1,500 r/min, mass about 45.3 kg. It is an open, preset-clearance unit with pressed-steel cages.
What is the difference between the NTN 430 and 432 double-row series at 140 mm bore?
Both are TDO double-row tapered roller units, but 430 is the light plan and 432 the heavy plan: at the same bore the 432 execution is wider and heavier with higher load ratings. 4T-430328XUUTG belongs to the light-duty 430-family TDO double-row series. Large sizes continue the plans as 4130/4131/4230/4231 (430 family) and 3230/3231 (432 family).
Can the internal clearance of 4T-430328XUUTG be adjusted at mounting?
No. The TDO unit — two cone assemblies against one double cup — is ground and set by NTN at the factory, and the 145 mm overall width is the finished dimension. Mounting sets no end play: seat the unit square, clamp the cup uniformly and verify free rotation. Field re-adjustment overloads one row.
What do the suffix letters on 430328XUUTG mean?
Suffix reading on 430328XUUTG: UTG marks the ULTAGE specification for large NTN tapered rollers — upgraded material and internal design, printed with the ＊ symbol ahead of the order number; U marks the uprated/reinforced internal design, a separate order number with higher capacity than the basic execution; X marks the boundary-dimension revision of the base number (D and width differ from the plain number of the same bore); suffixed variants are separate order numbers and are not interchangeable articles.
Why does 4T-430328XUUTG list two speeds, 1,100 and 1,500 r/min?
The lower figure, 1,100 r/min, is the grease-lubricated limiting speed for the two rows and their cages. With oil lubrication NTN rates 4T-430328XUUTG at 1,500 r/min because oil removes heat from both roller rows better — the housing feed must reach both rows through the double cup.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.