HH224335-HH224310 bearing: complete specifications & equivalents
The HH224335-HH224310 is a ANSI ABMA 19.2 radial bearing sized 101.6 x 212.725 x 66.675 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 101.6 mm |
| Outer diameter D | 212.725 mm |
| Width B | 66.675 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 635 kN |
| Basic static load rating C0 | 810 kN |
| Limiting speed (mechanical) | 1700 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 11300 g |
| Manufacturer designation | NTN 4T-HH224335/HH224310 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 4 in |
|---|---|
| Outer diameter D | 8.375 in |
| Width B | 2.625 in |
| ISO bore code | 35 |
| Radial section height (D−d)/2 | 55.6 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 119 of 148 |
| Bore above smallest 4t-inch-series size | 88.89999999999999 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HH224335-310 | SKF | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HH224335-HH224310 model number is decoded
4T-HH224335/HH224310 belongs to the NTN inch 4T tapered roller range (extra-heavy HH family); cone and cup are ordered by their own references and are individually interchangeable with like-numbered parts. Unlike ISO 355 metric numbers, this ABMA code does not encode the bore arithmetically: HH224335 identifies the cone of 101.6 mm (4 in) bore by catalogue lookup, and HH224310 fixes the 212.725 mm OD. Contact-angle geometry of the extra-heavy HH family gives 4T-HH224335/HH224310 its radial/axial load split — at 635/810 kN the static rating is about 1.28× C, typical of inch tapered sets proportioned for combined duty. The printed 635/810 kN ratings belong to the assembled HH224335+HH224310 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. Mount the 101.6 mm cone with an induction heater (max 120 °C) and press the 212.725 mm cup with a sleeve; driving either ring through the rollers brinells the raceways.
Typical equipment & failure modes
Common applications
- heavy truck and bus drive-axle differentials
- plant gearboxes on inch-dimensioned shaft lines
- large conveyor head pulleys in bulk-handling plant
- paper-machine and calender roll supports
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- cage damage from a mounting blow transmitted through the roller complement
- indentation of the raceways by hard particles in an open, unsealed arrangement
Selection pitfalls — read before you substitute
- Mount the 101.6 mm cone by induction heating (max 120 °C) and the 212.725 mm cup with a press sleeve; at 11300 g a cocked ring brinells the raceway directly.
- The extra-heavy HH family is proportioned for a high thrust share; swapping to a lighter LM or pure-numeric series at the same 101.6 mm bore cuts axial capacity even when the envelope fits — re-verify the load split before downgrading.
- ABMA makes the 101.6×212.725 mm envelope interchangeable, not the ratings: NTN prints 635/810 kN for this execution and another make of the same number can differ in roller complement.
- ABMA makes the 101.6×212.725 mm envelope interchangeable, not the ratings: NTN prints 635/810 kN for this execution and another make of the same number can differ in roller complement.
- Inch and metric bores collide on paper — 101.6 mm is 4 in, not a round metric size; a metric bearing that seems 0.1 mm off will not seat on the inch shaft.
- The 635/810 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-HH224335/HH224310; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-HH224335/HH224310?
4T-HH224335/HH224310 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 101.6 mm bore (4 in), 212.725 mm outside diameter and 66.675 mm assembled width T (8.375 × 2.625 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 635 kN, C0 810 kN, grease limiting speed 1,700 r/min, oil speed 2,300 r/min, mass about 11300 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-HH224335/HH224310 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the HH224335 cone or the HH224310 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 635/810 kN ratings change with the cup.
What is the difference between 4T-HH224335/HH224310 and a metric ISO 355 tapered bearing?
4T-HH224335/HH224310 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 101.6×212.725×66.675 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-HH224335/HH224310 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare HH224335/HH224310 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-HH224335/HH224310 list two speeds, 1,700 and 2,300 r/min?
The lower figure, 1,700 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-HH224335/HH224310 at 2,300 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.