HM803145-HM803110 bearing: complete specifications & equivalents
The HM803145-HM803110 is a ANSI ABMA 19.2 radial bearing sized 41.275 x 88.9 x 30.162 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 41.275 mm |
| Outer diameter D | 88.9 mm |
| Width B | 30.162 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 104 kN |
| Basic static load rating C0 | 125 kN |
| Limiting speed (mechanical) | 4300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 902 g |
| Manufacturer designation | NTN 4T-HM803145/HM803110 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1.625 in |
|---|---|
| Outer diameter D | 3.5 in |
| Width B | 1.187 in |
| ISO bore code | 45 |
| Radial section height (D−d)/2 | 23.8 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 47 of 148 |
| Bore above smallest 4t-inch-series size | 28.575 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HM803145 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HM803145-HM803110 model number is decoded
4T-HM803145/HM803110 is the NTN 4T catalogue entry for a 41.275×88.9×30.162 mm inch tapered roller bearing — an ABMA-dimensioned cone/cup set, not an ISO 355 metric bearing, even though the table quotes metric equivalents. Letter prefixes inherited from the inch convention mark the load family: LM reads as light-medium, HM as heavy-medium, LL as extra-light, J-prefixed codes as metric-envelope families — HM803145 sits in the heavy-medium HM family. Imperial cross-check for the drawing: 41.275×88.9×30.162 mm converts to 1.625 × 3.5 × 1.187 in; the ABMA envelope swaps with like-numbered inch parts but the 104/125 kN ratings are NTN-specific. Cup-side note for HM803110: within the heavy-medium HM family tables the HM803145 cone is listed against several cup options, and it is the cup that fixes the 88.9 mm OD and the 30.162 mm assembled width — quote the full HM803145/HM803110 pair, never the cone alone. Minimum load matters at speed: an unloaded 4T-HM803145/HM803110 run near 4,300 r/min lets the rollers skid; lightly spring-preload high-speed pair arrangements.
Typical equipment & failure modes
Common applications
- agricultural tractor transmission and PTO shafts
- industrial gearboxes built to inch shafting
- construction-equipment pivot and wheel positions
- mining and quarry conveyor drive pulleys
Known failure patterns
- rib-face scoring when the thrust share of the combined load exceeds what the cone rib of this size carries
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- cage damage from a mounting blow transmitted through the roller complement
- brinell marks on cone and cup raceways from impact during handling or hammer fitting
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 41.275 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-HM803145/HM803110.
- The heavy-medium HM family is proportioned for a high thrust share; swapping to a lighter LM or pure-numeric series at the same 41.275 mm bore cuts axial capacity even when the envelope fits — re-verify the load split before downgrading.
- Do not confuse T (30.162 mm, the assembled cone-plus-cup width) with the cone width when drawing spacers; an abutment sized to T leaves the cup unseated.
- Quote the full HM803145/HM803110 pair at ordering: the HM803145 cone also ships against sibling cups, and a cup from another reference changes the 30.162 mm assembled width and the rating.
- ABMA makes the 41.275×88.9 mm envelope interchangeable, not the ratings: NTN prints 104/125 kN for this execution and another make of the same number can differ in roller complement.
- The 104/125 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-HM803145/HM803110; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-HM803145/HM803110?
4T-HM803145/HM803110 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 41.275 mm bore (1.625 in), 88.9 mm outside diameter and 30.162 mm assembled width T (3.5 × 1.187 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 104 kN, C0 125 kN, grease limiting speed 4,300 r/min, oil speed 5,800 r/min, mass about 902 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-HM803145/HM803110 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the HM803145 cone or the HM803110 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 104/125 kN ratings change with the cup.
What is the difference between 4T-HM803145/HM803110 and a metric ISO 355 tapered bearing?
4T-HM803145/HM803110 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 41.275×88.9×30.162 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-HM803145/HM803110 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare HM803145/HM803110 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-HM803145/HM803110 list two speeds, 4,300 and 5,800 r/min?
The lower figure, 4,300 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-HM803145/HM803110 at 5,800 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.