HM804846-HM804810 bearing: complete specifications & equivalents
The HM804846-HM804810 is a ANSI ABMA 19.2 radial bearing sized 47.625 x 95.25 x 30.162 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 47.625 mm |
| Outer diameter D | 95.25 mm |
| Width B | 30.162 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 120 kN |
| Basic static load rating C0 | 147 kN |
| Limiting speed (mechanical) | 4000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 979 g |
| Manufacturer designation | NTN 4T-HM804846/HM804810 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1.875 in |
|---|---|
| Outer diameter D | 3.75 in |
| Width B | 1.187 in |
| ISO bore code | 46 |
| Radial section height (D−d)/2 | 23.8 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 59 of 148 |
| Bore above smallest 4t-inch-series size | 34.925 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HM804846-810 | SKF | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | Model-number interchange per ISO 15; confirm dimensions, sealing and ratings in the supplier catalogue. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HM804846-HM804810 model number is decoded
4T-HM804846/HM804810 belongs to the NTN inch 4T tapered roller range (heavy-medium HM family); cone and cup are ordered by their own references and are individually interchangeable with like-numbered parts. The 4T prefix is NTN's tapered roller quality mark stamped on both parts; it is a brand mark, not a size code, so cross-references quote HM804846/HM804810 without it. Speed planning uses both catalogue columns: grease 4,000 r/min is the mechanical ceiling for 4T-HM804846/HM804810, oil 5,300 r/min with circulating oil — a 1,300 r/min margin at this size. Housing fitment sequence for 4T-HM804846/HM804810: press the HM804810 cup square into the 95.25 mm seat first, then bring the HM804846 cone (on its 47.625 mm shaft) into adjustment — the two references are separate engineering parts that happen to ship as one set. With a rotating shaft a k5/m5 cone seat and an easy-push cup seat are typical practice for 4T-HM804846/HM804810; reverse the fit logic when the cup rotates.
Typical equipment & failure modes
Common applications
- truck and trailer axle hubs on inch-dimensioned axles
- agricultural tractor transmission and PTO shafts
- industrial gearboxes built to inch shafting
- construction-equipment pivot and wheel positions
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- edge loading when shaft deflection exceeds the few arc-minutes an adjusted pair tolerates
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 47.625 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-HM804846/HM804810.
- The heavy-medium HM family is proportioned for a high thrust share; swapping to a lighter LM or pure-numeric series at the same 47.625 mm bore cuts axial capacity even when the envelope fits — re-verify the load split before downgrading.
- Grease packs must leave free volume inside the 30.162 mm-wide set; over-greasing a pair churning near the oil-band speed of 5,300 r/min raises temperature and destroys the setting.
- Fit selection follows the rotating ring: a rotating cone on a 47.625 mm shaft takes a k5/m5 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- Fit selection follows the rotating ring: a rotating cone on a 47.625 mm shaft takes a k5/m5 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- The 120/147 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-HM804846/HM804810; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-HM804846/HM804810?
4T-HM804846/HM804810 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 47.625 mm bore (1.875 in), 95.25 mm outside diameter and 30.162 mm assembled width T (3.75 × 1.187 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 120 kN, C0 147 kN, grease limiting speed 4,000 r/min, oil speed 5,300 r/min, mass about 979 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-HM804846/HM804810 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the HM804846 cone or the HM804810 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 120/147 kN ratings change with the cup.
What is the difference between 4T-HM804846/HM804810 and a metric ISO 355 tapered bearing?
4T-HM804846/HM804810 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 47.625×95.25×30.162 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-HM804846/HM804810 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare HM804846/HM804810 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-HM804846/HM804810 list two speeds, 4,000 and 5,300 r/min?
The lower figure, 4,000 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-HM804846/HM804810 at 5,300 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.