HM804848-HM804810 bearing: complete specifications & equivalents
The HM804848-HM804810 is a ANSI ABMA 19.2 radial bearing sized 48.412 x 95.25 x 30.162 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 48.412 mm |
| Outer diameter D | 95.25 mm |
| Width B | 30.162 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel |
| Basic dynamic load rating C | 120 kN |
| Basic static load rating C0 | 147 kN |
| Limiting speed (mechanical) | 4000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 967 g |
| Manufacturer designation | NTN 4T-HM804848/HM804810 |
| Standard | ANSI ABMA 19.2 |
| Catalog version | NTN 2203E 2026-09-25 |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN 2203E 2026-09-25) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN 2203E 2026-09-25); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 4t-inch-series range
| Bore d | 1.906 in |
|---|---|
| Outer diameter D | 3.75 in |
| Width B | 1.187 in |
| ISO bore code | 48 |
| Radial section height (D−d)/2 | 23.4 mm |
| Smallest bore in 4t-inch-series | 12.7 mm |
| Largest outer diameter in 4t-inch-series | 260 mm |
| Width range across 4t-inch-series | 10.998–77.788 mm |
| Bore position in 4t-inch-series (smallest first) | 60 of 148 |
| Bore above smallest 4t-inch-series size | 35.712 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| HM804848 | ISO 15 | full Dimensions and internal design equivalent — standard interchange. | ISO 15 boundary-dimension envelope; brand-specific OEM equivalents (NSK/FAG/NTN) pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HM804848-HM804810 model number is decoded
The NTN 2203E inch table prints 4T-HM804848/HM804810 at 48.412 mm bore (1.906 in), 95.25 mm cup OD and 30.162 mm assembled T, with a grease limiting speed of 4,000 r/min and an oil ceiling of 5,300 r/min. Cone and cup of 4T-HM804848/HM804810 are separately stocked parts: a worn HM804810 cup can be replaced against the existing HM804848 cone, provided the new cup carries the identical reference — pairing across references changes the 30.162 mm assembled width and the rating. Grease relubrication at the 4,000 r/min limiting speed targets the cone-rib contact; sustaining 5,300 r/min needs an oil supply directed at the large roller ends. The printed 120/147 kN ratings belong to the assembled HM804848+HM804810 pair; a sibling row using the same cone with a different cup carries its own rating row because the raceway track shifts with the cup. A single-row tapered bearing reacts thrust in one direction only; 4T-HM804848/HM804810 is adjusted against a second bearing so the shaft is located in both directions.
Typical equipment & failure modes
Common applications
- construction-equipment pivot and wheel positions
- mining and quarry conveyor drive pulleys
- machine-tool headstocks on inch spindles
- pump and blower drive shafts with combined load
Known failure patterns
- cone-rib and roller large-end smearing when the adjusted pair runs with preload but starved lubricant film
- cup creep and housing fretting when the cup seat is cut too loose for the rotating load
- flaking on one cone only when a bent shaft loads the O/X pair unevenly
- pressed-steel cage pocket wear from roller skid at light radial load and high speed
- water-induced pitting when the open bearing sees washdown without external seals
Selection pitfalls — read before you substitute
- Hub and pinion positions of this 48.412 mm class are adjusted in pairs; verify end play against the axle or gearbox drawing and re-torque after bedding-in instead of trusting the first setting on 4T-HM804848/HM804810.
- The heavy-medium HM family is proportioned for a high thrust share; swapping to a lighter LM or pure-numeric series at the same 48.412 mm bore cuts axial capacity even when the envelope fits — re-verify the load split before downgrading.
- Fit selection follows the rotating ring: a rotating cone on a 48.412 mm shaft takes a k5/m5 seat, and a rotating cup reverses the logic — decide from the load diagram, not from habit.
- Replacing one half of an adjusted pair without resetting end play negates the 30.162 mm T logic: re-adjust the set and re-verify the contact pattern rather than reusing the old spacer stack.
- An unloaded 4T-HM804848/HM804810 near 4,000 r/min lets rollers skid and smear the cone rib; spring-preload lightly loaded high-speed pairs.
- The 120/147 kN ratings here are NTN Ball and Roller Bearings CAT.No.2203E figures for 4T-HM804848/HM804810; internal geometry legitimately differs between inch-series makers, so re-verify ratings, adjustment and the exact cone/cup references before substituting another brand on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 4T-HM804848/HM804810?
4T-HM804848/HM804810 is an inch-series single-row tapered roller bearing to the ABMA boundary plan: 48.412 mm bore (1.906 in), 95.25 mm outside diameter and 30.162 mm assembled width T (3.75 × 1.187 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 120 kN, C0 147 kN, grease limiting speed 4,000 r/min, oil speed 5,300 r/min, mass about 967 g. It is an open, separable cone/cup set with a pressed-steel cage.
Are the cone and cup of 4T-HM804848/HM804810 interchangeable separately?
Yes — ABMA inch parts are individually interchangeable: the HM804848 cone or the HM804810 cup can be replaced by an identical reference from NTN or another ABMA-dimensioned maker. Pairing the cone with a different cup reference is a different catalogue row: OD, assembled T and the 120/147 kN ratings change with the cup.
What is the difference between 4T-HM804848/HM804810 and a metric ISO 355 tapered bearing?
4T-HM804848/HM804810 follows the ABMA inch boundary plan with cone/cup references; ISO 355 bearings use metric dimension-series numbers (302, 322, …). Even where a metric size looks close to 48.412×95.25×30.162 mm, the envelopes and contact angles differ — the two systems are not drop-in interchangeable; check every boundary value before substituting.
What does the 4T prefix on 4T-HM804848/HM804810 mean?
4T is NTN's tapered roller bearing quality mark, stamped on cone and cup in the factory. It identifies NTN's 4T programme and is not a dimension or variant code, so interchange lists quote the bare HM804848/HM804810 references; the 4T spelling is retained among this page's search aliases.
Why does 4T-HM804848/HM804810 list two speeds, 4,000 and 5,300 r/min?
The lower figure, 4,000 r/min, is the grease-lubricated limiting speed — the mechanical ceiling for the cage, rollers and cone-rib contact. With oil lubrication NTN rates 4T-HM804848/HM804810 at 5,300 r/min because oil removes rib-contact heat better. Real limits still depend on pair adjustment, oil flow and cooling.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN 2203E 2026-09-25 on 2026-10-01. Read our editorial & correction policy.