361200-R bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 14 cam rollers) · extracted 2026-10-14

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 14 cam rollers); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 361200-R model number is decoded

the 32 mm outside diameter is the crowned track contact surface, the 10 mm bore takes the pin and the 9 mm overall width spreads the Hertzian contact across the thick-walled outer ring published ratings C 4.68 kN and C0 2.04 kN already include the outer-ring bending correction that track rollers require; the C/C0 ratio of 2.29 reflects a single deep groove ball set fatigue load limit Pu 0.085 kN against a 10 mm bore gives 0.47 kN per mm of bore, and the 12,000 r/min figure is a mechanical limit rather than a thermal one the maximum permissible radial loads are Fr 3.45 kN dynamically and F0r 5 kN statically; because the permissible static load is the lower of F0r and C0, the 2.04 kN figure governs static selection here the 9 mm width carries 0.52 kN per mm, the ring section measures 11.0 mm between bore and track surface, and 40 g over a 32x9 mm envelope is 0.139 g per mm2 of projected area for high-speed cam duty the catalogue sizes cam rollers on ISO 15 with the outside diameter excepted: bore 10 mm and width 9 mm follow the 62 series, but the 32 mm ring OD sits 2 mm proud of the 30 mm base-bearing diameter so that the track contact area is increased with a 10 mm bore this sizes into the miniature end of the cam roller range; the 9 mm width and 32 mm OD suit narrow track profiles and small-pitch indexing cams 3612.. R is the single row cam roller: heat stabilised to at least 120 degC, rated with internal clearance C3, and sealed rather than shielded so it needs no relubrication in normal duty the ring profile here is crowned (400 mm radius) rather than flat, which is the standard SKF cam roller surface and the reason a single row roller tolerates modest track angularity typical duties are conveyor diverters and transfer stations, sheet metal forming press feeds and tube and wire drawing guides this size is regularly specified for conveyor diverters and transfer stations and sheet metal forming press feeds, where the 32 mm ring rides the cam profile and the 10 mm bore takes a g6 pin the single ball row and the 9 mm wide ring make tube and wire drawing guides a natural fit; the 40 g mass keeps the follower inertia low enough for rapid indexing cycles the crowned running surface is standard, so the track must still be a smooth continuous profile — a step or weld spatter on the cam will brinell the ball raceway the NBR contact seals make this a greased-for-life unit; adding a relubrication line is pointless and forcing grease past the lips can dislodge them

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• heat stabilisation here only reaches 120 degC, so exposure to higher temperatures will dimensionally destabilise the rings and shorten the seal life
• the crowned running surface is standard, so the track must still be a smooth continuous profile — a step or weld spatter on the cam will brinell the ball raceway
• the NBR contact seals make this a greased-for-life unit; adding a relubrication line is pointless and forcing grease past the lips can dislodge them