361202-R bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 14 cam rollers) · extracted 2026-10-14

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 14 cam rollers); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 361202-R model number is decoded

the 40 mm outside diameter is the crowned track contact surface, the 15 mm bore takes the pin and the 11 mm overall width spreads the Hertzian contact across the thick-walled outer ring published ratings C 7.02 kN and C0 3.2 kN already include the outer-ring bending correction that track rollers require; the C/C0 ratio of 2.19 reflects a single deep groove ball set fatigue load limit Pu 0.137 kN against a 15 mm bore gives 0.47 kN per mm of bore, and the 9,500 r/min figure is a mechanical limit rather than a thermal one the maximum permissible radial loads are Fr 5.1 kN dynamically and F0r 7.35 kN statically; because the permissible static load is the lower of F0r and C0, the 3.2 kN figure governs static selection here the 11 mm width carries 0.64 kN per mm, the ring section measures 12.5 mm between bore and track surface, and 72 g over a 40x11 mm envelope is 0.164 g per mm2 of projected area for medium-high-speed cam duty the 15 mm bore and 11 mm width are those of the 62 series ball bearing at the same size code, while the 40 mm outside diameter is 5 mm larger than that bearing's 35 mm OD — this follows the SKF rule that cam rollers keep the ISO 15 dimension series except for the outside diameter the 15 mm bore falls in the small band, the workhorse size for general cam drives, packaging machine linkages and conveyor diverters where the 40 mm crowned ring rides directly on the cam profile the 3612 designation means the lightest cam roller design in the chapter, based on a single deep groove ball set; the R suffix marks the NBR contact seals that keep the factory grease fill in place for life the crowned running surface is standard on this design — the 40 mm ring is ground to a radius of 400 mm so that a slightly misaligned or deflecting track does not concentrate load on one edge typical duties are woodworking machinery feed cams, bottle filling carousel cams and automatic assembly line actuators this size is regularly specified for woodworking machinery feed cams and bottle filling carousel cams, where the 40 mm ring rides the cam profile and the 15 mm bore takes a g6 pin the single ball row and the 11 mm wide ring make automatic assembly line actuators a natural fit; the 72 g mass keeps the follower inertia low enough for rapid indexing cycles the single row design has the lowest tilting-moment capacity in the chapter; if the cam track is not parallel to the roller axis, the load moves onto one edge of the ring heat stabilisation here only reaches 120 degC, so exposure to higher temperatures will dimensionally destabilise the rings and shorten the seal life

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• the pin must be machined to g6; an undersized or worn pin lets the inner ring creep and changes the effective internal clearance
• the single row design has the lowest tilting-moment capacity in the chapter; if the cam track is not parallel to the roller axis, the load moves onto one edge of the ring
• heat stabilisation here only reaches 120 degC, so exposure to higher temperatures will dimensionally destabilise the rings and shorten the seal life