170×360×72 mm bearings

14 models from 3 brands across 3 types share this ISO 15 envelope: 170 mm bore, 360 mm outside diameter, 72 mm width (6.693×14.173×2.835 in), 95 mm radial section.

14 models fit this space 3 brands 14 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6334 Deep Groove Ball SKF open CN 312 340 31000
6334-M Deep Groove Ball SKF open CN 312 340 35000
6334-NSK Deep Groove Ball NSK open CN 360 355 36600
6334-NTN Deep Groove Ball NTN open CN 360 355 30700
7334 Angular Contact Ball NTN open CN 430 485 35300
7334-BCBM Angular Contact Ball SKF open CN 390 490 36000
7334B Angular Contact Ball NTN open CN 395 445 35300
N334 Cylindrical Roller NTN open CN 885 1010 36100
NF334 Cylindrical Roller NTN open CN 885 1010 36100
NJ334 Cylindrical Roller NTN open CN 885 1010 36100
NU334 Cylindrical Roller NTN open CN 885 1010 36100
NU334-ECM Cylindrical Roller SKF open CN 952 1180 33000
NUP334 Cylindrical Roller NTN open CN 885 1010 36100
QJ-334-N2MA Angular Contact Ball SKF open CN 655 1040 41500

Note: catalogue dynamic load ratings for this envelope span 312.0– 952.0 kN — a 205% spread between designs in the very same 170×360×72 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 170 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6334, 6334-M, 6334-NSK, 6334-NTN, 7334, 7334-BCBM, 7334B, N334, NF334, NJ334, NU334, NU334-ECM, NUP334, QJ-334-N2MA.

Frequently asked questions

Are all 170×360×72 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 170 mm bore, 360 mm OD, 72 mm width (6.693×14.173×2.835 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 14 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 170×360×72?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 170×360×72 mm in inches?

170×360×72 mm converts to 6.693×14.173×2.835 in, with a 95 mm (3.740 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6334, 6334-M, 6334-NSK mount in the same space despite different internal designs.