70×150×51 mm bearings

24 models from 3 brands across 5 types share this ISO 15 envelope: 70 mm bore, 150 mm outside diameter, 51 mm width (2.756×5.906×2.008 in), 40 mm radial section.

24 models fit this space 3 brands 24 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
22314 Spherical Roller SKF open CN 413 430 4550
22314-EK Spherical Roller SKF open CN 413 430 5350
22314EAD1 Spherical Roller NTN open CN 420 396 4250
22314EAKD1 Spherical Roller NTN open CN 420 396 4160
22314EMD1 Spherical Roller NTN open CN 420 396 4310
22314EMKD1 Spherical Roller NTN open CN 420 396 4220
2314 Self-Aligning Ball NTN open — 111 37.5 3900
62314-2RS Deep Groove Ball SKF 2RS CN 104 68 3750
C2314 CARB Toroidal Roller SKF open CN 405 430 4300
C2314-K CARB Toroidal Roller SKF open CN 405 430 4300
N2314 Cylindrical Roller NTN open CN 247 262 3900
N2314EA Cylindrical Roller NTN open CN 325 325 3950
NF2314EA Cylindrical Roller NTN open CN 325 325 3950
NJ2314 Cylindrical Roller NTN open CN 247 262 3900
NJ2314-ECP Cylindrical Roller SKF open CN 315 325 4000
NJ2314EA Cylindrical Roller NTN open CN 325 325 3950
NJG2314-VH Cylindrical Roller SKF open CN 336 400 4400
NU2314 Cylindrical Roller NTN open CN 247 262 3900
NU2314-ECP Cylindrical Roller SKF open CN 315 325 3950
NU2314EA Cylindrical Roller NTN open CN 325 325 3950
NUP2314 Cylindrical Roller NTN open CN 247 262 3900
NUP2314-ECP Cylindrical Roller SKF open CN 315 325 4150
NUP2314EA Cylindrical Roller NTN open CN 325 325 3950
SL192314-XL Cylindrical Roller FAG open CN 385 385 4330

Note: catalogue dynamic load ratings for this envelope span 104.0– 420.0 kN — a 304% spread between designs in the very same 70×150×51 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 70 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 22314, 22314-EK, 22314EAD1, 22314EAKD1, 22314EMD1, 22314EMKD1, 2314, 62314-2RS, C2314, C2314-K, N2314, N2314EA, NF2314EA, NJ2314, NJ2314-ECP, NJ2314EA, NJG2314-VH, NU2314, NU2314-ECP, NU2314EA, NUP2314, NUP2314-ECP, NUP2314EA, SL192314-XL.

Frequently asked questions

Are all 70×150×51 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 70 mm bore, 150 mm OD, 51 mm width (2.756×5.906×2.008 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 24 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 70×150×51?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 70×150×51 mm in inches?

70×150×51 mm converts to 2.756×5.906×2.008 in, with a 40 mm (1.575 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 22314, 22314-EK, 22314EAD1 mount in the same space despite different internal designs.