7307-BECBM bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7307-BECBM model number is decoded

7307 BECBM is SKF's 35 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 35×80×21 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. machined brass cage, ball-centred (suffix M), the choice for high speed, marginal lubrication and shock duty. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 35×80×21 mm (1.378×3.15×0.827 in), 22.5 mm radial section height, C 41.5 kN, C0 26.5 kN, Pu 1.14 kN.reference speed 11,000 r/min (thermal) and limiting speed 14,000 r/min (mechanical), catalogue mass 450 g. Envelope economics: the 21 mm width over a 22.5 mm section yields 0.93 mm of ring width per section millimetre, and the bearing weighs 450 g for 41.5 kN of dynamic capacity — about 11 g per rated kN. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 14,000 r/min while thermal balance under catalogue load sets the 11,000 r/min reference; at dm ≈ 57.5 mm the corresponding dn is approximately 805k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 11,000 r/min against a 14,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.79. Cage detail specific to this order number: the M cage is a one-piece machined brass window cage centred on the balls, chosen for high speeds, thin-film lubrication and shock loads; it is heavier and stiffer than the stamped Y-cage execution and tolerates interrupted oil supply far better than the PA66 or PEEK alternatives. Do not substitute the stamped-brass BECBY order number expecting identical cage behaviour.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• One 7307-BECBM locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.
• Do not mix execution classes inside one set: a universally matchable BECBM unit is ground for arbitrary pairing, a basic execution is not.
• Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.
• DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.
• The steep 40° angle of 7307-BECBM favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBM bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.