7307-NTN bearing: complete specifications & equivalents
The 7307-NTN is a ISO 15 radial bearing sized 35 x 80 x 21 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 35 mm |
| Outer diameter D | 80 mm |
| Width B | 21 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 44 kN |
| Basic static load rating C0 | 26.3 kN |
| Fatigue load limit Pu | 2.05 kN |
| Limiting speed (mechanical) | 9800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 462 g |
| Manufacturer designation | NTN 7307 |
| Standard | ISO 15 |
| Catalog version | NTN Ball and Roller Bearings CAT.No.2203E |
| Last verified | 2026-10-01 |
Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203E) · extracted 2026-10-01
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203E); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 7300-series range
| Bore d | 1.378 in |
|---|---|
| Outer diameter D | 3.15 in |
| Width B | 0.827 in |
| ISO bore code | 07 |
| Radial section height (D−d)/2 | 22.5 mm |
| Smallest bore in 7300-series | 10 mm |
| Largest outer diameter in 7300-series | 420 mm |
| Width range across 7300-series | 11–80 mm |
| Bore position in 7300-series (smallest first) | 8 of 32 |
| Bore above smallest 7300-series size | 25 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 7307 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×80×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 7307-ACCBM | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×80×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 7307-BE-2RZP | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×80×21 mm envelope per ISO 15; seal variant (OPEN vs RSR) and load ratings differ — confirm sealing and rating before substituting. |
| 7307-BECBM | SKF | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 7307-BECBP | SKF | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 7307-BECBY | SKF | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 7307-BEGAPH | SKF | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 7307-BEP | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 35×80×21 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 7307-NTN model number is decoded
7307 is an NTN single-row angular contact ball bearing: heavy-duty 7300 single-row family, listed in NTN Ball and Roller Bearings CAT.No.2203E at 35 x 80 x 21 mm. NTN builds the number from 73 is the single-row dimension series (heavy-duty 7300 single-row family), then 07 encodes the 35 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 30 deg contact angle is the lever that turns the 26.3 kN static rating into useful one-direction thrust capacity. When axial load reverses, specify the bearing as a matched pair (DB, DF or DT) instead of two random singles — the catalogue right-hand columns give the paired ratings for exactly this reason. Mount with the thrust against the marked face: the contact angle runs from the low shoulder of the inner ring to the high shoulder of the outer ring, and reversing it throws the capacity away.
Typical equipment & failure modes
Common applications
- machine-tool spindle cartridges and driven tooling
- industrial pump and blower impeller shafts
- gearbox input shafts under helical-gear thrust
- electric motor shafts with axial locating duty
Known failure patterns
- impact brinelling dents on the 30 deg contact path after a shaft-side hammer blow during mounting, because axial shock travels straight through the contact angle
- loss of preload after housing-fret or shaft creep, leaving the pair loose — ball skidding, cage rattle and a falling natural frequency follow
- pressed-steel cage pocket wear and rivet loosening after repeated ball skid at light load and high speed
- edge loading and early spalling from housing bores that are out of round or shoulders that are too small for the ring face
- flaking that starts at the raceway shoulder on the thrust-loaded side when axial load repeatedly exceeds the design share
Selection pitfalls — read before you substitute
- In this size class the common miss is lubrication interval, not fit — a 35 mm spindle at the catalogue speeds needs a calculated relubrication plan, not a calendar one.
- The standard 30 deg bearing and its B (40 deg) sibling share the envelope; picking between them is a load-direction decision, not a quality upgrade.
- Substituting the B (40 deg) execution for the standard 30 deg bearing changes the axial/radial load split — the shaft position and the mating bearing see different forces even though the envelope is identical.
- If the application vibrates at standstill (transport, idle machine next to a running line), specify protection: the contact ellipse of a preloaded bearing false-brinells faster than a loose one.
- A 7307 mounted the wrong way round still turns smoothly by hand; the failure shows up weeks later as raceway flaking on the unloaded-looking side.
- The 44/26.3 kN ratings and 2.05 kN Pu here are NTN Ball and Roller Bearings CAT.No.2203E figures for 7307; internal geometry legitimately differs between manufacturers, so re-verify ratings, contact angle and suffix before substituting another make on a rated drive.
Frequently asked questions
What are the dimensions and catalogue ratings of NTN 7307?
7307 is a single-row angular contact ball bearing to ISO 15: 35 mm bore, 80 mm outside diameter, 21 mm width (1.378 x 3.15 x 0.827 in). From NTN Ball and Roller Bearings CAT.No.2203E: C 44 kN, C0 26.3 kN and a 2.05 kN fatigue load limit Pu; the grease limiting speed is 9,800 r/min and the oil rating 13,000 r/min; mass about 462 g.
How is the 7307 designation structured?
73 is the single-row dimension series (heavy-duty 7300 single-row family); 07 encodes the 35 mm bore (bore code x 5); with no letter after the digits it is the standard 30 deg contact-angle execution — the 40 deg version carries a B. The 80 mm OD and 21 mm width follow the ISO 15 boundary-dimension plan for that series.
Which axial direction does 7307 support?
One 7307 alone takes thrust in one direction only, along its 30 deg contact angle; reversing thrust calls for a second bearing or a factory-matched DB/DF/DT pair (the catalogue right-hand columns list the paired ratings). Radial load is always carried as a combined load through the angled contact.
What lubrication speeds does NTN print for 7307?
Per NTN Ball and Roller Bearings CAT.No.2203E, the grease limiting speed is 9,800 r/min and the oil rating 13,000 r/min. These are catalogue ceilings for a correctly mounted bearing with the stated lubricant; preload, fill quantity, ambient heat and paired arrangements all move the real limit.
What should be checked before substituting another make for 7307?
The 35/80/21 mm envelope is ISO 15 interchangeable, but internal geometry — contact angle, osculation, cage and shoulder details — is maker-specific. Re-verify C 44 kN / C0 26.3 kN, the speed figures, contact angle and suffix meaning against the donor catalogue before swapping on a rated drive.
Reviewed & verified by the MPN Base engineering desk against source catalog NTN Ball and Roller Bearings CAT.No.2203E on 2026-10-01. Read our editorial & correction policy.