7314-BECBP bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7314-BECBP model number is decoded

7314 BECBP is SKF's 70 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 70×150×35 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 127 kN, C0 98 kN, Pu 3.9 kN.reference speed 5,600 r/min (thermal) and limiting speed 5,600 r/min (mechanical), which coincide for this size, catalogue mass 2650 g. The 3.9 kN fatigue load limit is the equivalent-load floor for long-life adjustment; with 127/98 kN ratings and 2650 g mass this execution carries about 1.81 kN of C per millimetre of bore. Load balance: C0 98 kN against C 127 kN gives a 0.77 ratio, typical of a steep-angle axial-oriented design; Pu 3.9 kN enters the SKF adjusted-life equation rather than the basic rating life. Bore-to-OD planning: OD 150 over bore 70 is a 2.14× step for this size, and the 35 mm width gives a bore/width ratio of 2.00; use these ratios when housing space around the 70 mm shaft is the first constraint. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Greased positions should fill roughly 25–35 % of the free volume on a 7314-BECBP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.
• One 7314-BECBP locates the shaft in one axial direction only; reversing-thrust positions need a DB or DF pair — or a double-row bearing — with preload set from the load diagram, never from assembly feel.
• Assign interference to the rotating ring — roughly k5 on a 70 mm rotating shaft with an H7 housing — and let the stationary ring slide for axial setting; reverse the logic if the outer ring rotates.
• At 70 mm bore the k5 seat assumes a steel shaft and housing; aluminium housings grow faster with temperature, so re-check the outer-ring setting when the case is non-ferrous.
• The steep 40° angle of 7314-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.