7314 bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB) · extracted 2026-09-26

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 3.1 single-row ACBB); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7314 model number is decoded

Ordering number 7314 BEP in the SKF Rolling Bearings catalogue denotes a single-row 40° angular-contact ball bearing for a 70 mm shaft, medium (7300) series, with an open PA66-caged execution and one-direction axial capacity.Digit by digit, 7314 reads as bearing type 7 (single-row angular contact), medium section diameter series 3, and bore reference 14 resolving to 70 mm; 150 mm OD and 35 width are the matching ISO 15 boundary values. The letters mean B = 40° angle, E = enhanced ball complement and race geometry, P = PA66 glass-fibre cage, so this 7314 is the open polymer-caged execution rather than the sealed or brass-cage catalogue variants. The 3.65 kN Pu figure feeds the SKF adjusted-life equation at contaminated or partial-film conditions, and the 0.76 C0/C balance shows this execution is tuned to thrust-heavy combined loads rather than pure radial running. Because the contact line runs at 40°, one 7314 reacts thrust in a single direction; bidirectional shafts need a DB or DF pair with defined preload, and a rotating inner ring on a 70 mm shaft typically takes a k5 seat with an H7 housing bore.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount the 70 mm bore 7314 by induction heating of the inner ring (max 120 °C — the PA66 cage sets the ceiling, not the steel); driving it home through the outer ring or balls brinells the asymmetric raceway.
• The 73xx medium section at 70 mm bore (150×35 mm) is heavier-rated than the 7214 but runs hotter at the same speed; do not substitute a 7314 into a 72-series spindle position without re-checking dn, lubricant film and preload.
• The 40° contact angle creates an induced axial load under pure radial force; include it in the 7314 rating calculation (and account for it in both bearings of a pair) or the unloaded bearing skids its balls.
• A single 7314 cannot locate the shaft axially in both directions; mounting it singly on a reversing-thrust shaft leaves one direction uncontrolled — always use a DB or DF matched pair for bidirectional location.
• The PA66 cage is rated for 120 °C continuous service; sustained hotter running (hot process gas, heat soak from a coupling) embrittles the cage — select the machined-brass BECBM execution for positions above that.
• The 119/90 kN ratings are SKF catalogue 17000 values for the 7314 BEP execution; SKF can revise internal geometry without changing the order number, so keep the catalogue version (PUB BU/P1 17000/1 EN, 2018) with the specification and re-verify for critical drives.
• SKF lists several executions of 7314 (BEP basic, BECBP universally matchable, BE-2RZP sealed, BECBM brass-cage, ACC-series at 25°); they are not interchangeable order numbers — quote the full 7314 BEP designation when purchasing and match the execution to the mounting arrangement.
• A plain 7314 BEP is a single open bearing, not a universally matchable one; to mount a defined DB/DF pair order the BECBP (CB) execution — pairing two unmatched basic units gives uncontrolled preload because the side faces are not ground for set mounting.