QJ-314-N2PHAS bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the QJ-314-N2PHAS model number is decoded

QJ 314 N2PHAS is SKF's 70 mm-bore QJ four-point contact ball bearing of the QJ300 series, 70×150×35 mm, with a two-piece inner ring for bidirectional axial location beside a radial bearing. QJ identifies a four-point contact ball bearing with a two-piece inner ring: the gothic-arch raceways seat each ball at four points, giving axial location in both directions while a paired radial bearing carries the radial load. N2 marks two locating slots, 180° apart, in one outer-ring side face: pins or dogs engage the slots to stop the outer ring turning in its radially-clear housing bore. glass-fibre reinforced PEEK cage, outer-ring-centred with lubrication grooves in the guiding surfaces (suffix PHAS), for very high-speed oil-air or grease lubrication. Envelope 70×150×35 mm (2.756×5.906×1.378 in), 40.0 mm radial section height, C 200 kN, C0 180 kN, Pu 7.35 kN.SKF publishes only the 8,000 r/min limiting speed for this execution, catalogue mass 3150 g. Load balance: C0 180 kN against C 200 kN gives a 0.90 ratio, typical of a four-point thrust-oriented design; Pu 7.35 kN enters the SKF adjusted-life equation rather than the basic rating life. Mass and section check: 3150 g inside the 70×150×35 mm outline leaves a 40.0 mm radial section, and the 180 kN static rating is 0.90× the dynamic rating — plan static safety and minimum load against those numbers rather than against sister executions. Speed-ratio note for this exact unit: no thermal reference speed is listed (seal/grease life governs), so the 8,000 r/min limiting value is the single published ceiling. Locating-slot execution: the two N2 notches are milled into one outer-ring side face exactly 180 degrees apart and engaged by housing dogs or headed pins during assembly; verify dog engagement by hand before the cover goes on, deburr the slot edges after any housing rework, and re-inspect the slot roots for fretting marks at each overhaul because a dog that rides only one slot lets the outer ring walk. The slots identify this order number unmistakably: the plain MA/PHAS execution of the same bore has no notches and must be secured differently.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Provide a minimum axial load (spring preload is common) so the balls stay correctly seated at speed and light-load conditions; otherwise they skid.
• Engage the N2 slots with housing dogs at assembly — a radially loose outer ring without positive anti-rotation creeps its seat
• The PHAS PEEK outer-ring-centred cage with lubrication grooves suits the highest speeds with oil-air lubrication
• Anti-rotation is built into QJ-314-N2PHAS: check the two N2 slot faces and the engaging housing dogs at every refit, and never rely on cover friction to stop the radially loose outer ring.
• The PHAS PEEK cage of QJ-314-N2PHAS is outer-ring-centred with lubrication grooves: feed clean oil-air or appropriate grease to the guide land and inspect groove filling at overhaul.
• Catalogue ratings are SKF PUB BU/P1 17000 figures for QJ 314 N2PHAS as the qj slotted execution; the other order numbers of the QJ 314 size are different products and may carry different ratings — always quote the full designation when purchasing.