7320-BECBP bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7320-BECBP model number is decoded

7320 BECBP is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 100×215×47 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. CB means universally matchable with Normal axial internal clearance: the two side faces are ground so any two units form DB (back-to-back), DF (face-to-face) or DT (tandem) sets without regrinding. Envelope 100×215×47 mm (3.937×8.465×1.85 in), 57.5 mm radial section height, C 216 kN, C0 208 kN, Pu 6.95 kN.reference speed 3,800 r/min (thermal) and limiting speed 4,000 r/min (mechanical), catalogue mass 7500 g. Selection figures for 7320 BECBP: the static-to-dynamic ratio C0/C is 0.96, Pu 6.95 kN is about 3 % of C, and catalogue mass works out to roughly 75 g per millimetre of bore. Speed planning distinguishes the two published ceilings mechanically: the cage and balls tolerate 4,000 r/min while thermal balance under catalogue load sets the 3,800 r/min reference; at dm ≈ 157.5 mm the corresponding dn is approximately 630k mm·r/min. Speed-ratio note for this exact unit: the reference speed is 3,800 r/min against a 4,000 r/min limiting speed, i.e. a reference-to-limit ratio of 0.95. Universal polymer-cage execution: BECBP is the factory-ground set-mounting version of the basic BEP — both side faces are finish-ground to a controlled stand-off so two units form DB, DF or DT arrangements without shims, while the glass-fibre PA66 ball-centred cage keeps the light, quiet running typical of the P-cage range; CB delivers Normal axial clearance before preload is applied at assembly.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.
• Fillet radii must clear the chamfer so the 47 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
• DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.
• Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.
• The steep 40° angle of 7320-BECBP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Universally matchable BECBP bearings arrive ready for set mounting, not preloaded sets: preload results from how the set is clamped, so follow the SKF stand-off-ring and nut-torque procedure.