7320-BEP bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 7320-BEP model number is decoded

7320 BEP is SKF's 100 mm-bore single-row angular-contact ball bearing in the 7300 series, nominal 40° (B) contact angle, 100×215×47 mm to the ISO dimension plan. 40° contact angle (suffix B): the steep standard single-row angle, giving the highest axial capacity at the cost of speed, with a recommended load ratio Fa/Fr ≥ 1. E marks the optimized internal design with an enhanced ball complement and race geometry. glass-fibre reinforced PA66 cage, ball-centred (suffix P), with a 120 °C continuous-temperature ceiling. The plain BEP is a basic single bearing: its faces are not ground for universal matching, so defined pairs require the BECBP execution rather than two arbitrary BEP units.. Envelope 100×215×47 mm (3.937×8.465×1.85 in), 57.5 mm radial section height, C 203 kN, C0 190 kN, Pu 6.4 kN.reference speed 3,800 r/min (thermal) and limiting speed 3,600 r/min (mechanical), catalogue mass 7500 g. Envelope economics: the 47 mm width over a 57.5 mm section yields 0.82 mm of ring width per section millimetre, and the bearing weighs 7500 g for 203 kN of dynamic capacity — about 37 g per rated kN. Selection figures for 7320 BEP: the static-to-dynamic ratio C0/C is 0.94, Pu 6.4 kN is about 3 % of C, and catalogue mass works out to roughly 75 g per millimetre of bore. Speed-ratio note for this exact unit: the reference speed is 3,800 r/min against a 3,600 r/min limiting speed, i.e. a reference-to-limit ratio of 1.06. Basic polymer-cage execution: BEP is delivered as an individual open bearing with the 40-degree optimized internals and a glass-fibre PA66 ball-centred cage; it is not ground on the side faces for arbitrary pairing, so a reversing-thrust position should order BECBP for a set rather than mounting two unmatched BEP units.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• DB pairs give the highest moment stiffness, DF pairs tolerate misalignment and thermal expansion better, DT shares heavy one-direction thrust; choose from the shaft thermal calculation rather than by habit.
• Greased positions should fill roughly 25–35 % of the free volume on a 7320-BEP of this section and route the surplus past the outer ring; overpacking churns the grease and reproduces the thermal preload problem mechanically.
• Reference and limiting speeds are different ceilings: design to both, and remember preload and oil/air cooling move the real thermal limit far from the catalogue reference value.
• Keep the load ratio in the SKF design range: Fa/Fr ≥ 1 for this angle; below it the balls unload the contact ellipse and skid, which is why the catalogue insists on a minimum axial load (Fam ≈ A·(n·dm/1000)²) at high speed.
• The steep 40° angle of 7320-BEP favours thrust-heavy combined loads; for a predominantly radial high-speed position the 25° ACCBM execution of the same size is the alternative order number.
• Catalogue ratings are SKF PUB BU/P1 17000 figures for 7320 BEP as the single basic pa66 execution; the other order numbers of the 7320 size are different products and may carry different ratings — always quote the full designation when purchasing.