MPNbase

100×215×47 mm bearings

40 models from 3 brands across 5 types share this ISO 15 envelope: 100 mm bore, 215 mm outside diameter, 47 mm width (3.937×8.465×1.850 in), 57.5 mm radial section.

40 models fit this space 3 brands 40 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
1320 Self-Aligning Ball NTN open — 140 57.5 8400
1320-K Self-Aligning Ball SKF open CN 143 57 8300
1320K Self-Aligning Ball NTN open — 140 57.5 8400
21320 Spherical Roller SKF open CN 433 490 8600
21320-EK Spherical Roller SKF open CN 433 490 10500
21320-NTN Spherical Roller NTN open CN 410 465 8890
21320K Spherical Roller NTN open CN 410 465 8780
6320 Deep Groove Ball NSK open CN 191 141 7040
6320-2RS Deep Groove Ball SKF 2RS CN 174 140 7200
6320-2RS-NSK Deep Groove Ball NSK 2RS CN 191 141 7040
6320-2RS-NTN Deep Groove Ball NTN 2RS CN 192 141 7000
6320-M Deep Groove Ball SKF open CN 174 140 8700
6320-NTN Deep Groove Ball NTN open CN 192 141 7000
6320-RSR Deep Groove Ball NSK RSR CN 191 141 7040
6320-RSR-NTN Deep Groove Ball NTN RSR CN 192 141 7000
6320-ZZ Deep Groove Ball SKF ZZ CN 174 140 7300
6320-ZZ-NSK Deep Groove Ball NSK ZZ CN 191 141 7040
6320-ZZ-NTN Deep Groove Ball NTN ZZ CN 192 141 7000
7320 Angular Contact Ball SKF open CN 203 190 7500
7320-BECBM Angular Contact Ball SKF open CN 216 208 7500
7320-BECBP Angular Contact Ball SKF open CN 216 208 7500
7320-BECBY Angular Contact Ball SKF open CN 216 208 7500
7320-BEM Angular Contact Ball SKF open CN 203 190 7500
7320-BEP Angular Contact Ball SKF open CN 203 190 7500
7320-NTN Angular Contact Ball NTN open CN 230 193 7180
7320B Angular Contact Ball NTN open CN 211 178 7320
N320 Cylindrical Roller NTN open CN 330 335 7320
N320-ECP Cylindrical Roller SKF open CN 450 440 7350
NF320 Cylindrical Roller NTN open CN 330 335 7320
NJ320 Cylindrical Roller NTN open CN 330 335 7320
NJ320-ECJ Cylindrical Roller SKF open CN 450 440 7650
NJ320E Cylindrical Roller NTN open CN 420 425 —
NU320 Cylindrical Roller SKF open CN 450 440 7450
NU320-NTN Cylindrical Roller NTN open CN 330 335 7320
NU320E Cylindrical Roller NTN open CN 420 425 —
NUP320 Cylindrical Roller NTN open CN 330 335 7320
NUP320-ECJ Cylindrical Roller SKF open CN 450 440 7700
NUP320E Cylindrical Roller NTN open CN 420 425 —
QJ-320-N2MA Angular Contact Ball SKF open CN 345 400 9300
QJ320 Angular Contact Ball NTN open CN 300 585 9140

Note: catalogue dynamic load ratings for this envelope span 140.0– 450.0 kN — a 221% spread between designs in the very same 100×215×47 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 100 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 1320, 1320-K, 1320K, 21320, 21320-EK, 21320-NTN, 21320K, 6320, 6320-2RS, 6320-2RS-NSK, 6320-2RS-NTN, 6320-M, 6320-NTN, 6320-RSR, 6320-RSR-NTN, 6320-ZZ, 6320-ZZ-NSK, 6320-ZZ-NTN, 7320, 7320-BECBM, 7320-BECBP, 7320-BECBY, 7320-BEM, 7320-BEP, 7320-NTN, 7320B, N320, N320-ECP, NF320, NJ320, NJ320-ECJ, NJ320E, NU320, NU320-NTN, NU320E, NUP320, NUP320-ECJ, NUP320E, QJ-320-N2MA, QJ320.

Frequently asked questions

Are all 100×215×47 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 100 mm bore, 215 mm OD, 47 mm width (3.937×8.465×1.850 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 40 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 100×215×47?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 100×215×47 mm in inches?

100×215×47 mm converts to 3.937×8.465×1.850 in, with a 57.5 mm (2.264 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 1320, 1320-K, 1320K mount in the same space despite different internal designs.