16100-ZZ bearing: complete specifications & equivalents
The 16100-ZZ is a ISO 15 radial bearing sized 10 x 28 x 8 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 10 mm |
| Outer diameter D | 28 mm |
| Width B | 8 mm |
| Material | GCr15 |
| Seal / shield | ZZ |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 5.07 kN |
| Basic static load rating C0 | 2.36 kN |
| Fatigue load limit Pu | 0.1 kN |
| Reference speed (thermal) | 60000 rpm |
| Limiting speed (mechanical) | 30000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 26 g |
| Manufacturer designation | 16100-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 16100-series range
| Bore d | 0.394 in |
|---|---|
| Outer diameter D | 1.102 in |
| Width B | 0.315 in |
| ISO bore code | 00 |
| Radial section height (D−d)/2 | 9 mm |
| Smallest bore in 16100-series | 10 mm |
| Largest outer diameter in 16100-series | 30 mm |
| Width range across 16100-series | 8–8 mm |
| Bore position in 16100-series (smallest first) | 1 of 2 |
| Bore above smallest 16100-series size | 0 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 16100 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 10×28×8 mm envelope and equivalent catalogue ratings; 16100 is the open arrangement execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 16100-ZZ model number is decoded
The 16100-series is SKF's extra-narrow large-OD deep-groove section; bore code 00 follows the 10/12/15/17 mm exception table, so 16100 fits a 10 mm shaft. The envelope is 10×28×8 mm (0.394×1.102×0.315 in) with a 9.0 mm radial section height, C 5.07 kN, C0 2.36 kN and Pu 0.1 kN. SKF spells the double shield 16100-2Z (suffix 2Z); the shields are non-contact, retain grease and block coarse debris but are not liquid-tight. Limiting speed 30000 r/min, catalogue mass 26 g. A thin section saves space but leaves little margin for misalignment or shaft deflection.
Typical equipment & failure modes
Common applications
- slew and indexing drives
- industrial electric motors
- gearboxes and speed reducers
- centrifugal and positive-displacement pumps
Known failure patterns
- fine-particle abrasion when non-contact shields let dust through in a dirty environment
- grease aging inside the shielded cavity with no relubrication path
- raceway smearing under marginal lubrication at start-up
- electrical pitting in VFD-driven motors without shaft grounding
Selection pitfalls — read before you substitute
- At 10 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
- Catalogue ratings for 16100-ZZ (C 5.07 kN, C0 2.36 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
- Shields on 16100-ZZ are non-contact: chips and coarse dust stay out, but water passes straight through — specify the sealed 16100-2RS for washdown duty.
- Do not pry the caps off 16100-ZZ to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
- Catalogue ratings for 16100-ZZ (C 5.07 kN, C0 2.36 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
- Mount by heating the inner ring (max 120 °C) — driving 16100-ZZ home through the outer ring or balls brinells the raceways.
Frequently asked questions
What are the dimensions of 16100-ZZ?
The SKF 16100-2Z measures 10 mm bore × 28 mm OD × 8 mm width (0.394 × 1.102 × 0.315 in), mass about 26 g. It has two non-contact sheet-metal shields.
How does the bore code in 16100 work?
Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 16100 fits a 10 mm shaft. Code × 5 starts at code 04.
What is the speed rating of 16100-ZZ?
SKF lists a 60000 r/min thermal reference speed and a 30000 r/min mechanical limiting speed for 16100-2Z; real limits also depend on lubrication and fits.
What is the difference between 16100-ZZ and a same-bore 62-series bearing?
Section height differs: 16100-ZZ has a 9 mm radial section and C 5.07 kN; always match d, D and B — same bore alone never makes two bearings interchangeable.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.