16100 bearing: complete specifications & equivalents

The 16100 is a ISO 15 radial bearing sized 10 x 28 x 8 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 28 mm d = 10 B = 8 mm side section front view
Principal dimensions: bore d 10 mm, outer diameter D 28 mm, width B 8 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 10 mm
Outer diameter D 28 mm
Width B 8 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 5.07 kN
Basic static load rating C0 2.36 kN
Fatigue load limit Pu 0.1 kN
Reference speed (thermal) 60000 rpm
Limiting speed (mechanical) 38000 rpm
Operating temperature -40 to +120 °C
Mass 24 g
Manufacturer designation 16100
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 16100-series range

Bore d0.394 in
Outer diameter D1.102 in
Width B0.315 in
ISO bore code00
Radial section height (D−d)/29 mm
Smallest bore in 16100-series10 mm
Largest outer diameter in 16100-series30 mm
Width range across 16100-series8–8 mm
Bore position in 16100-series (smallest first)1 of 2
Bore above smallest 16100-series size0 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
16100-ZZ SKF full
Dimensions and internal design equivalent — standard interchange.
Same 10×28×8 mm envelope and equivalent catalogue ratings; 16100-2Z is the two non-contact shields execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 16100 model number is decoded

The 16100-series is SKF's extra-narrow large-OD deep-groove section; bore code 00 follows the 10/12/15/17 mm exception table, so 16100 fits a 10 mm shaft. The envelope is 10×28×8 mm (0.394×1.102×0.315 in) with a 9.0 mm radial section height, C 5.07 kN, C0 2.36 kN and Pu 0.1 kN. The open 16100 carries no shields or seals and relies on application lubrication and external sealing. Limiting speed 38000 r/min, catalogue mass 24 g. A thin section saves space but leaves little margin for misalignment or shaft deflection.

Typical equipment & failure modes

Common applications

  • space-constrained gearboxes
  • clutch and transmission assemblies
  • robotics and automation joints
  • lay shafts and idler shafts

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • edge loading from shaft deflection or housing misalignment
  • rolling-contact fatigue spalling once the catalogue L10 life is exceeded

Selection pitfalls — read before you substitute

  • Do not preload 16100 to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • Do not preload 16100 to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • Open 16100 needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 16100; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • The fatigue load limit is 0.1 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
  • Fillet radii must clear the 16100 chamfer so the 8 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.

Frequently asked questions

What are the dimensions of 16100?

The SKF 16100 measures 10 mm bore × 28 mm OD × 8 mm width (0.394 × 1.102 × 0.315 in), mass about 24 g. It is open, with no shields or seals.

How does the bore code in 16100 work?

Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 16100 fits a 10 mm shaft. Code × 5 starts at code 04.

What is the difference between 16100 and a same-bore 62-series bearing?

Section height differs: 16100 has a 9 mm radial section and C 5.07 kN; always match d, D and B — same bore alone never makes two bearings interchangeable.

Which fits should I use for 16100?

With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 28 mm housing; reverse the interference if the outer ring rotates.

How heavy is 16100?

Catalogue mass is 24 g for 16100; seal and cage executions of the same envelope differ by a few grams.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.