215-ZZ bearing: complete specifications & equivalents
The 215-ZZ is a ISO 15 radial bearing sized 75 x 130 x 25 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 75 mm |
| Outer diameter D | 130 mm |
| Width B | 25 mm |
| Material | GCr15 |
| Seal / shield | ZZ |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 72.1 kN |
| Basic static load rating C0 | 72 kN |
| Fatigue load limit Pu | 3 kN |
| Reference speed (thermal) | 9000 rpm |
| Limiting speed (mechanical) | 4300 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 1250 g |
| Manufacturer designation | 215-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 200-series range
| Bore d | 2.953 in |
|---|---|
| Outer diameter D | 5.118 in |
| Width B | 0.984 in |
| ISO bore code | 15 |
| Radial section height (D−d)/2 | 27.5 mm |
| Smallest bore in 200-series | 30 mm |
| Largest outer diameter in 200-series | 180 mm |
| Width range across 200-series | 16–34 mm |
| Bore position in 200-series (smallest first) | 10 of 15 |
| Bore above smallest 200-series size | 45 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6215-RSR | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | NSK bearing NSK 6215VV on the same 75×130×25 mm envelope, but catalogue C/C0 differ (72.1/72 kN vs 73/49.5 kN) — envelope interchange only after a load check. |
| 6215-M | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 75×130×25 mm envelope as SKF 6215 M, but catalogue C/C0 differ (72.1/72 kN vs 68.9/49 kN) — envelope match only after a load check. |
| 215 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 75×130×25 mm envelope and equivalent catalogue ratings; 215 is the open arrangement execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 6215 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6215 shares the 75×130×25 mm envelope but catalogue C/C0 differ (72.1/72 kN vs 68.9/49 kN) — envelope match, not a load-rating equivalent. |
| 6215-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6215-2Z shares the 75×130×25 mm envelope but catalogue C/C0 differ (72.1/72 kN vs 68.9/49 kN) — envelope match, not a load-rating equivalent. |
| 6215-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6215-2RS1 shares the 75×130×25 mm envelope but catalogue C/C0 differ (72.1/72 kN vs 68.9/49 kN) — envelope match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 215-ZZ model number is decoded
215-2Z is a filling-slot (notched-ring) deep-groove bearing in the legacy 200-series: the last two digits encode the bore: 215 carries code 15 = 75 mm (code × 5). The rings carry loading slots that allow extra balls during assembly, which is what gives the 75×130×25 mm envelope its C 72.1 kN and C0 72 kN ratings (Pu 3 kN). SKF spells the double shield 215-2Z (suffix 2Z); the shields are non-contact, retain grease and block coarse debris but are not liquid-tight. Limiting speed 4300 r/min, mass 1250 g. These bearings are built for high purely-radial loads at moderate speeds.
Typical equipment & failure modes
Common applications
- farm machinery and harvesters
- construction equipment drives
- hoists and winch gear trains
- eccentric and vibratory conveyors
Known failure patterns
- spalling of the filling-slot edge when balls are hammered through the slot under heavy thrust loading
- dirt entering through the open slot area when external sealing is neglected
- cage damage from running beyond the limiting speed
- raceway smearing under marginal lubrication at start-up
Selection pitfalls — read before you substitute
- Filling slots let more balls be packed into the 75×130 mm envelope, which is why 215-ZZ reaches C 72.1 kN — but the slots also mean the two rings separate when the balls align with them, so handle it as a loose-clearance design.
- The slots sit at one angular position: on 215-ZZ, never pass the full radial load across the slot zone during mounting or the ring lip can crack.
- 215 uses the legacy SKF 200/300 numbering (light/heavy filling-slot series), not the modern 6200/6300 spelling; quote 215-2Z exactly when ordering replacements.
- Filling-slot bearings take heavy purely-radial load at moderate speed but little thrust; the 72.1/72 kN ratings assume radial loading — use deep-groove 6xxx where axial load matters.
- Filling slots let more balls be packed into the 75×130 mm envelope, which is why 215-ZZ reaches C 72.1 kN — but the slots also mean the two rings separate when the balls align with them, so handle it as a loose-clearance design.
- Deep-groove geometry tolerates only minutes of misalignment; if the 130 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming 215-ZZ.
Frequently asked questions
What are the dimensions of 215-ZZ?
Filling-slot bearing 215-2Z measures 75×130×25 mm (2.953×5.118×0.984 in), about 1250 g.
What does the designation 215 mean?
It is the legacy 200/300 filling-slot numbering: series 200 and bore code 15 = 75 mm. Filling-slot bearings predate the 6xxx deep-groove spelling.
Why use an old 200-series bearing instead of a 62xx?
For slow, heavy, purely-radial duty the extra balls give more capacity in the same bore, and the separable rings simplify assembly in blind housings; at high speed modern designs run better.
What fails on 215-ZZ?
Slot-edge chipping under thrust or shock, dirt ingress in the open design and cage wear past the 4300 r/min limiting speed are the typical failure modes.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.