6215-ZZ-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6215-ZZ-NTN model number is decoded

In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6215 carries bore code 15 = 75 mm. Outside diameter 130 mm and width 25 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 75 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN catalogue order number: 6215ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 75 mm bore, induction heating to roughly 80–100 °C is the clean mounting method; never exceed 120 °C, and hold 6215 against the shaft shoulder while it cools so the ring cannot creep back.
• The 62xx light series is the default general-purpose section at 75 mm bore; before upgrading to a 6315 for extra capacity, confirm the housing accepts a 130 mm OD and 25 mm width — it is not a drop-in swap.
• Do not wash 6215-ZZ-NTN in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Shielded 6215-ZZ-NTN units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
• Do not quieten a noisy bearing by preloading it: the 6200-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 6200-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• NTN catalogues the shielded version as 6215ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NTN order number when buying through an NTN channel.
• At 75 mm bore 6215 is in NTN's upper general-purpose range; the pressed-steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• NTN lists the grease limiting speed at 4800 r/min for 6215; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 73.5 kN dynamic load rating (C) and 49.5 kN static (C0), 3.8 kN fatigue load limit Cu, 6215 is a heavy-load bearing for industrial gearboxes and large conveyors; NTN expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 1180 g (1.2 kg), 6215 needs mechanical handling for mounting; NTN recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 75×130×25 mm envelope of 6215 gives a D/d ratio of 1.73 and 27.5 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 73.5/49.5 kN load ratings, 3.8 kN fatigue load limit Cu NTN lists the grease limiting speed at 4800 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 1180 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6215ZZ on the 75×130×25 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6215 in a rated drive.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.