219-ZZ bearing: complete specifications & equivalents
The 219-ZZ is a ISO 15 radial bearing sized 95 x 170 x 32 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 95 mm |
| Outer diameter D | 170 mm |
| Width B | 32 mm |
| Material | GCr15 |
| Seal / shield | ZZ |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 121 kN |
| Basic static load rating C0 | 122 kN |
| Fatigue load limit Pu | 4.5 kN |
| Reference speed (thermal) | 6700 rpm |
| Limiting speed (mechanical) | 4000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 2700 g |
| Manufacturer designation | 219-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 200-series range
| Bore d | 3.74 in |
|---|---|
| Outer diameter D | 6.693 in |
| Width B | 1.26 in |
| ISO bore code | 19 |
| Radial section height (D−d)/2 | 37.5 mm |
| Smallest bore in 200-series | 30 mm |
| Largest outer diameter in 200-series | 180 mm |
| Width range across 200-series | 16–34 mm |
| Bore position in 200-series (smallest first) | 14 of 15 |
| Bore above smallest 200-series size | 65 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6219-RSR | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | NSK bearing NSK 6219VV on the same 95×170×32 mm envelope, but catalogue C/C0 differ (121/122 kN vs 120/82 kN) — envelope interchange only after a load check. |
| 6219-M | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 95×170×32 mm envelope as SKF 6219 M, but catalogue C/C0 differ (121/122 kN vs 114/81.5 kN) — envelope match only after a load check. |
| 219 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 95×170×32 mm envelope and equivalent catalogue ratings; 219 is the open arrangement execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 6219 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6219 shares the 95×170×32 mm envelope but catalogue C/C0 differ (121/122 kN vs 114/81.5 kN) — envelope match, not a load-rating equivalent. |
| 6219-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6219-2Z shares the 95×170×32 mm envelope but catalogue C/C0 differ (121/122 kN vs 114/81.5 kN) — envelope match, not a load-rating equivalent. |
| 6219-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF SKF 6219-2RS1 shares the 95×170×32 mm envelope but catalogue C/C0 differ (121/122 kN vs 114/81.5 kN) — envelope match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 219-ZZ model number is decoded
219-2Z is a filling-slot (notched-ring) deep-groove bearing in the legacy 200-series: the last two digits encode the bore: 219 carries code 19 = 95 mm (code × 5). The rings carry loading slots that allow extra balls during assembly, which is what gives the 95×170×32 mm envelope its C 121 kN and C0 122 kN ratings (Pu 4.5 kN). SKF spells the double shield 219-2Z (suffix 2Z); the shields are non-contact, retain grease and block coarse debris but are not liquid-tight. Limiting speed 4000 r/min, mass 2700 g. These bearings are built for high purely-radial loads at moderate speeds.
Typical equipment & failure modes
Common applications
- legacy machinery repairs
- slew drives
- material-handling winches
- slow heavy gearboxes
Known failure patterns
- spalling of the filling-slot edge when balls are hammered through the slot under heavy thrust loading
- dirt entering through the open slot area when external sealing is neglected
- rolling-contact fatigue spalling once the catalogue L10 life is exceeded
- brinelling from static overload or hammer blows during mounting
Selection pitfalls — read before you substitute
- 219 uses the legacy SKF 200/300 numbering (light/heavy filling-slot series), not the modern 6200/6300 spelling; quote 219-2Z exactly when ordering replacements.
- Filling-slot bearings take heavy purely-radial load at moderate speed but little thrust; the 121/122 kN ratings assume radial loading — use deep-groove 6xxx where axial load matters.
- Shields on 219-ZZ retain grease but do not seal against water; for wet farm duty add external lip seals rather than trusting the shield.
- Limiting speed is just 4000 r/min: filling-slot cages and the slot geometry run cooler below that — overspeed drives cage wear and smearing.
- Shields on 219-ZZ retain grease but do not seal against water; for wet farm duty add external lip seals rather than trusting the shield.
- Do not preload 219-ZZ to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
Frequently asked questions
What are the dimensions of 219-ZZ?
Filling-slot bearing 219-2Z measures 95×170×32 mm (3.74×6.693×1.26 in), about 2700 g.
What does the designation 219 mean?
It is the legacy 200/300 filling-slot numbering: series 200 and bore code 19 = 95 mm. Filling-slot bearings predate the 6xxx deep-groove spelling.
Is 219-ZZ available sealed?
Shielded executions (-2Z, listed here as 219-ZZ) exist; contact-sealed versions are generally not produced for the filling-slot family.
What is a filling-slot bearing?
The inner and outer rings each have a loading slot; when aligned, extra balls can be inserted, raising radial rating (C 121 kN for 219-ZZ). The slots also make the rings separable.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.