61802-2RS-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61802-2RS-NSK model number is decoded

61802-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 15 by five gives the 15 mm bore; the 24 mm outside diameter and 5 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 15 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NSK's contact-seal catalogue number is 6802DD (suffix DDU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 15 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 61802 with C3 clearance and re-check the residual value after mounting.
• The 618xx thin section at 15 mm bore has only a 4.5 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6215.
• Heat is the enemy of the sealed 61802-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Never wash a sealed 61802-2RS-NSK in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 5 mm-wide ring of 61802-2RS-NSK drags the lip and overheats it.
• The housing bore for the 24 mm OD should be round within IT7; an oval bore pinches the outer ring of 61802-2RS-NSK and shows up later as two-point loaded raceway wear.
• NSK catalogues the contact-sealed version as 6802DD (suffix DDU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. NSK's DDU lip design is single-lip contact, so grease life is longer than VV but drag torque is higher.
• At 15 mm bore the 61802 sits in NSK's small-bore range; NSK ships these sizes with a pressed-steel cage and P0 tolerance as standard, and NSK's EA (extra-precision) or P5 class is a special-order upgrade for spindle duty — do not assume catalogue P0 figures hold for instrument use without an NSK engineering check.
• At 2.28 kN dynamic load rating (C) and 1.26 kN static (C0), 61802 is a light-load NSK bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 7 g, 61802 is a lightweight NSK bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 15×24×5 mm envelope of 61802 gives a D/d ratio of 1.60 and 4.5 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 2.28/1.26 kN load ratings, mass 7 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6802DD on the 15×24×5 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61802 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 61802; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• When replacing a failed unit, inspect the shaft and housing seats before fitting the new 61802 — a new bearing pressed onto a worn or oval seat reproduces the original failure mode in a fraction of its expected life.