61802-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61802-RSR-NTN model number is decoded

In the 61800-series (diameter series 8 of ISO 15) the last two digits encode the bore: 61802 carries bore code 15 = 15 mm. Outside diameter 24 mm and width 5 mm come from the ISO 15 boundary-dimensions general plan. Suffix -RSR denotes two low-friction non-contact elastomer seals; they keep coarse debris out with minimal drag but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 15 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6802LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 15 mm bore, induction heating to roughly 80–100 °C is the clean mounting method; never exceed 120 °C, and hold 61802 against the shaft shoulder while it cools so the ring cannot creep back.
• Only 4.5 mm of radial section separates bore and OD on the 618xx series at 15 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6215.
• RSR low-friction seals on 61802-RSR-NTN run faster than contact-seal 61802-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 61802-2RS instead.
• The non-contact lip of 61802-RSR-NTN does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 15 mm bore position before relying on it as sealed-for-life.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 5 mm-wide ring of 61802-RSR-NTN drags the lip and overheats it.
• The housing bore for the 24 mm OD should be round within IT7; an oval bore pinches the outer ring of 61802-RSR-NTN and shows up later as two-point loaded raceway wear.
• NTN catalogues this low-friction non-contact seal as 6802LLB (suffix LB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• At 15 mm bore the 61802 sits in NTN's small-bore range; ABEC-1/P0 runout is standard, and the pressed-steel cage is adequate up to the grease limiting speed — for higher accuracy (spindles, instruments) ask NTN for a P6 or P5 tolerance-class listing before relying on catalogue P0 figures.
• The 26000 r/min grease limiting speed puts 61802 in NTN's high-speed range; at these speeds relubrication interval shortens sharply and the pressed-steel cage must be checked for cage-bar critical speed.
• At 2.3 kN dynamic load rating (C) and 1.26 kN static (C0), 0.09 kN fatigue load limit Cu, 61802 is a light-load bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 7 g, 61802 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 15×24×5 mm envelope of 61802 gives a D/d ratio of 1.60 and 4.5 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 2.3/1.26 kN load ratings, 0.09 kN fatigue load limit Cu NTN lists the grease limiting speed at 26000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 7 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6802LLB on the 15×24×5 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61802 in a rated drive.
• Factory-fill grease in NTN sealed units is a general-duty lithium-soap grease; food-grade, low-temperature and high-temperature fills are request options at order time, because LLU/LLB units are not meant to be opened and re-greased in the field.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.