61802-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61802-NTN model number is decoded

61802 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 15 by five gives the 15 mm bore; the 24 mm outside diameter and 5 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 15 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 15 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 61802 with C3 clearance and re-check the residual value after mounting.
• Only 4.5 mm of radial section separates bore and OD on the 618xx series at 15 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6215.
• Storage matters for open bearings: 61802-NTN leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61802 units.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 24 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 61802-NTN.
• Do not quieten a noisy bearing by preloading it: the 61800-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• The open 61802 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• At 15 mm bore the 61802 sits in NTN's small-bore range; ABEC-1/P0 runout is standard, and the pressed-steel cage is adequate up to the grease limiting speed — for higher accuracy (spindles, instruments) ask NTN for a P6 or P5 tolerance-class listing before relying on catalogue P0 figures.
• The 26000 r/min grease limiting speed puts 61802 in NTN's high-speed range; at these speeds relubrication interval shortens sharply and the pressed-steel cage must be checked for cage-bar critical speed.
• At 2.3 kN dynamic load rating (C) and 1.26 kN static (C0), 0.09 kN fatigue load limit Cu, 61802 is a light-load bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 7 g, 61802 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 15×24×5 mm envelope of 61802 gives a D/d ratio of 1.60 and 4.5 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 2.3/1.26 kN load ratings, 0.09 kN fatigue load limit Cu NTN lists the grease limiting speed at 26000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 7 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6802 on the 15×24×5 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61802 in a rated drive.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 61802 is listed.